PYLE Audio CD Player PLCD27 User Manual

R
PLCD27  
WNER'S MANUAL  
CD PLAYER  
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
 
To prevent injury of fire,take the  
following precautions:  
To prevent damage to the machine,  
take the following precautions:  
Attaching panel  
Attach the front panel by fixing  
the left side of it into this unit as1  
showing.Then push the right side  
of panel towards into connecting  
plug as 2 showing.  
Insert the unit unitll it is firmly locked to the  
main unit, otherwise it may  
Be sure the unit is connected to a 12V  
DC power with a Negative Ground  
fall out of place when jolted  
The unit is only designed for use with 4  
speakers. Do not combine output for use  
with 2 speakers. Do not ground negative  
speaker leads to the chassis ground  
Do not open the top cover and do not install  
the unit in  
When extending the ignition, memory  
back up or ground cable, use diameter of  
0.75mm(AWG18) or  
more automotive grade cable to avoid wire  
deterioration or damage  
to the wire coating.  
place where it is exposed to direct sunlight  
(including the faceplate),in order to avoid high  
heat or humidity, water splash over it or dust.  
Do not touch the terminals of the units.  
Attaching panel  
To prevent short circuit, never put or leave  
any metallic object into the unit.  
If you smell or see smoke, turn off the  
power immediately and consult your dealer.  
Be careful not to drop or shock the unit  
strongly, it may break or crack because it  
contain glass parts.  
If you have difficulty in installing this unit  
in your vehicle. Please contact your dealer.  
If the unit seems not work in properly press  
the reset buttonto reset the memory of the  
unit.  
2
 
POWER ON/  
OFF/VOLUME  
Volume  
PLAY/PAUSE  
EJECT  
Increasing volume  
EJECT  
Rotate the [VOL+]button  
VOL  
Decreasing  
Rotate the [VOL-]button  
BD  
CD  
PUSH  
ON/OFF  
TOP  
SCAN  
REPEAT  
RANDOM  
STOP  
DSP  
CLK  
1
2
3
4
5
6
SELECT  
CLOCK  
RELEASE SELECT DSP  
Play/pause  
Play  
Press the [CD]button  
LCD display  
Pause  
Press again the [CD]button  
Power  
Turning ON the power  
If a disc has already been loaded, CDIN would be shown on  
the display, press this button to start play disc even though  
the unit is in Radio mode. When disc  
is playing, press this button to  
Press the [PWR]button.  
pause the disc, press again  
Press to turn on the unit power,Press the button to turn off  
the unit.  
to resume the normal play.  
BD  
CD  
DOM  
STOP  
CLK  
5
6
3
 
Hour  
Eject  
Press [  
] button to adjust the hour.  
Out  
Minute  
Press the [ ]button ,if having adisc in the unit.  
The disc will be ejected out.  
Press [ ] button to adjust the minute.  
Quit clock set mode  
If there no operation in 5 second, it will quit clock  
set mode.  
In  
Press the [ ]button again, the disc  
will be load in.  
In beam mode, press the BD button can enter radio  
mode. If the disc in the slot, press the EJECT button to  
eject the disc form the slot and automatically be  
switched to the radio mode.  
LOUD/DSP  
LOUD  
In radio mode, if push a disc into slot, the disc will  
automatic insert and begins to play. If the disc in the solt,  
press PLAY/PAUSE button to play the disc again.  
Long press the DSP button to emphasize the bass output,  
press it again to resume the normal listening.  
DSP  
Short press this button to DSP  
Press DSP button once, ROCK will bicker on display.  
Press DSP button twice, POP will bicker on display.  
Press DSP button third, CLASS will bicker on display.  
Clock  
Press CLK can display time. Time will display even  
power off.  
Long Press CLK for 3 second will into clock set mode.  
Release  
press the "  
" button to release faceplate.  
4
 
VOL+/-  
Speaker mode  
EJECT  
VOL  
VOLUME  
TREBLE  
BASS  
BD  
CD  
PUSH  
ON/OFF  
TOP  
1
SCAN  
REPEAT  
RANDOM  
STOP  
DSP  
CLK  
2
3
4
5
6
SELECT  
FADER  
BALANCE  
SCAN  
RANDOM  
REPEAT  
SELECT  
TOP  
STOP  
In press mode, VOL is sel function  
Treble set mode  
Volume set mode  
Press SEL button third,  
display shows TRE ,then  
rotate the volume button to adjust treble  
Press SEL button once,display shows VOL  
then rotate the volume button  
to adjust volume level up.Rotate  
the volume button to  
,
+
+
VOL  
level up. Rotate the volume  
treble level down.  
-
buttonto adjust  
-
SEL  
adjust volume  
level down.  
PRESS  
Balance set mode  
SELECT  
Press SEL button fourth  
display shows BAL ,then  
PRESS  
rotate the volume  
to adjust left speaks level .  
Rotate the volume button  
to adjust right speaks level .  
+
button  
Bass set mode  
-
Press SEL button twice,display shows BAS  
then rotate the volume button to adjust bass  
button to adjust  
,
+
level up. Rotate the volume  
bass level down.  
-
Fader set mode  
Press SEL button fifth,display shows FAD ,then  
rotate the volume button to adjust front speaks  
buttonto adjust back  
+
level. Rotate the volume  
speaks level.  
-
5
 
Top  
Scan  
Press [TOP]button  
Press [SCN]button  
Select the first track directly  
Press this button once for TRACK INTRODUCTION,the first  
ten seconds of each track on the disc will paly. To confirm  
the track number. Press it again while playing on the desired  
track. SCAN will appear on the display.Press it again to  
stop it.  
In CD mode,press this button, the first track will play.  
Repeat  
Press [RPT]button  
Stop  
Press the button once to repeat the same track continuously,  
Press the button twice to repeat the disc continuously,  
RPT will appear on the LCD display.  
Press [STOP]button  
Press this button once to stop play music .  
Random  
Press [RDM]button  
Press this button to play all the track inrandom order. RDM  
will appear on the display. Press it again to stop random playing.  
This button is invalid ifthe unit is in PBC On mode.  
6
 
SEEK- SEEK+  
Tune  
In radio mode:  
EJECT  
manual tuning:  
VOL  
short press  
Short press  
button it can select higher frequency station.  
can select lower frequency station.  
BD  
CD  
PUSH  
ON/OFF  
TOP  
SCAN  
REPEAT  
RANDOM  
STOP  
CLK  
DSP  
1
2
3
4
5
6
SELECT  
Auto loading tuning:  
the long press  
button it can automatically select higher  
BAND  
PRESET MEMORY 1-6  
frequency station. And the long press  
select lower frequency station.  
it can automatically  
Band  
Selecting band  
Press BAND button to select among three FM or two AM bands.  
(FM1-FM2-FM3-AM1-AM2)  
ST  
Frequency  
7
 
Loading and replacing the battery  
Use one lithium battery(CR2025)  
insert the batteries with the +and - poles aligned properly.  
Following the illustration inside the case.  
Pull out  
APS  
MONO  
TOP  
LOUD  
CLK  
STOP  
Store unused batteries out of the reach of children. Contact a  
doctor immediately if the battery is accidentally swallowed.  
RPT  
Do not set the remote on hot places such as above the dashboard.  
SCAN  
Basic operation  
RDM  
Turning ON the power  
Press the [ ]button.  
Press to turn on the unit power,Press the button to turn off  
the unit.  
8
 
External view  
........ Number of items  
External view  
........ Number of items  
Volume  
Increasing volume  
Press the [+]loud VOL  
Increasing volume  
Press the [-]low VOL  
1
2
5
6
............1  
............1  
............1  
............1  
Play/pause  
Play  
Press the [ ]button  
Pause  
3
4
7
8
............1  
............2  
............1  
............1  
Press the [ ] button again  
APS  
MONO  
TOP  
LOUD  
CLK  
STOP  
RPT  
SCAN  
RDM  
Radio control  
Page(7)  
The use of any accessories except of those provided  
might result in damage to the unit .make sure only to  
use the accessories shipped with the unit ,as shown  
above.  
Remote operation the same  
of mainframe.  
9
 
Follow this easy wiring diagram in order to enable you to install  
the new or existing RADIO and SPEAKER wring system.  
SPEAKER WIRING  
The unit is only designed for the use with 4 speakers system, it can  
only be connected with speakers rated in the load impedance range  
from 4 to 8 ohms. Load impedance less than 4 ohms could damage  
the unit.  
Be sure the unit is connected to a 12 volts battery with negative ground.  
Good ground connections eliminate most electrical noise problem and  
require tight with the metal vehicle chassis. remove plastic, paint or dust  
for good electrical contact.  
Never combine (BRIDGE) the outputs for use with 2 speakers, and  
Never ground any Negative speaker to the chassis ground.  
CAR ANTENNA  
RED RCH  
CAR ANTENNA  
LCH RCA line out  
RED RCH  
WHITE  
RCA line out  
WHITE LCH  
Connect to control for antenna  
or remote control for amplifier.  
Orange  
YELLOW  
Memory+  
Grey  
Green  
Connect to battery or +12 volts of  
power source that is always live.  
Green  
/white  
Grey  
/white  
Black  
Red  
Ground-  
Right Front  
Left Front  
Brown  
Blue  
12V+  
Brown  
/white  
Blue  
/white  
Connect to lgnition key switch.  
Right Rear  
Left Rear  
10  
 
Before installing the receiver permanently, fit it in the approximate place in your car Connect the  
equipment according to the speakers and electrical connections. When  
your system is operated properly,(preferably with the  
car engine running), follow the instructions  
for permanent installation  
of your system.  
3)Support strap  
(supplied)  
INSTALL THE UNIT  
1)Install half sleeve, can be with or  
without adapter. It will fit better  
with adapter.  
2)Bend over some tabs where possible  
2)Bend over tabs  
of half sleeve  
(supplied)  
tosecure the half sleeve inside of dash.  
3) Support strap to bestrutted under  
dash, secure this strip to avoid skipp  
ing of disc.  
1) Adapter  
(not supplied)  
Half sleeve  
(supplied)  
REMOVING THE UNIT  
Insert removal wrench into the small  
gap on the right side of the unit and pull  
the unit slightly out on the same side,  
then release the wrench. Repeat the  
same action for the left side. By now,  
you can remove the unit and unplug  
the wires connector.  
4) Two wrenches for release  
the unit (supplied)  
11  
 
Specifications subject to change without notice.  
CD PLAYER  
GENERAL  
Signal/Noise radio......................................................70dB  
Frequency response..............................20Hz-20KHz(+3dB)  
Channel separation..................................................>45dB  
Dual D/A converter.......................................................16Bit  
Operating power.....................................12 Volts DC,negative  
ground  
%10THD output wiring.........................Designed for using four  
speakers only front and rear  
channels cannot be combined  
in use with 2speakers.  
FM Tuner  
Load impedance..................................compatible 4 to 8 ohm  
speakers  
Tuning range............................................USA:87.5-108MHz  
(100KHz step)  
Fuses........................................................1amp and 10 amp  
Dimensions...........................................178mm(L)x50mm(W)  
x150mm(H)  
EUROPE:87.5-108.0MHz  
(50KHz step)  
FM usable sensitivity(S/N=30dB)..............................<12dB  
Stereo separation.....................................................>45dB  
Weight......................................................................2.5Kgs  
AM Tuner  
Tuning range...........................................USA:520-1720KHz  
(10KHz step)  
EUROPE:522-1620KHz  
(9KHz step)  
AM sensitivity..............................................................28dB  
12  
 
What might seem to be a malfunction in your unit may  
just be the result of slight misoperation or miswiring.  
Before calling service, first check the following table  
for possible problems.  
?No/Poor sound on one or more speakers  
Speakers or speaker wiring or volume, Balance and  
Fader setting  
Check the speaker wiring and test the speakers all in good condition  
check the setting of volume, Balance and Fader controls.  
?The power does not turn ON.  
The fuse has blown.  
Install half sleeve, can be with or  
?CD sound skips  
Installation the unit angle is greater than 45 ,or  
mounting is not fixed and the back strap is not secure.  
?NO Sound.  
The cable connect incorrectness.  
Adjust the unit with mounting angle less than 45 and make sure the  
unit is mounted securely and tighten with the back strap(supplied)  
Exactitude connect of the cable.  
?Noise on Radiopoor recepiton  
Antenna and Antenna Cable.  
?Unit completely inoperative, no Light and Sound  
Incorrect wire connection, Power RED/YELLOW or  
Ground wire or Blown fuse  
Check antenna and antenna cable, the antenna base must be  
grounded and connected with good condition, repace  
antenna or antenna cable if needed.  
Check the Red wire to +12 Volts with key lgnition witch, yellow wire to  
+12 Volts battery and black wire to ground. Check Fuse with red/yellow  
wire, or check the fuse block on your car.  
?Noise on both Radio and CD  
Poor ground,dirty or corroded at the car Battery posts  
Check the black wire for proper grounding clean and tighten ground  
connection.  
13  
 
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
 

Paxar Network Card PPT 2700 User Manual
Philips CD Player AJ3150 User Manual
Philips DVD Player MDV450 User Manual
Philips Indoor Furnishings SB7S17A User Manual
Philips Stereo System OTT2000 User Manual
Pioneer Flat Panel Television PRO 950HD User Manual
Pioneer Musical Toy Instrument 750K User Manual
Planet Technology Network Card WL U356M User Manual
Plantronics Headphones S11 User Manual
Primera Technology Printer LX 810 User Manual