PYLE Audio Car Stereo System PLVRL6400 User Manual

PLVRL6400  
OWNER’S MANUAL  
FLIP DOWN TFT MONITOR  
 
INSTALLATION  
Ceiling-on Installation  
Bracket  
Levers  
Tapping Screws (M4x10)  
Fixing holes  
Mounting Bolts (M3x6)  
Fig. 2  
1. Determine the mounting location and drill four mounting holes.  
2. Attach the bracket to the holes with the tapping screws (M4x10).  
3. Let the two levers aim at the fixing holes to fix the display unit.  
4. Attach the unit to the bracket with the mounting bolts (M3x6).  
5. When the installation has completed, you can also turn the display upward or  
downward, left or right to adjust the viewing angle.  
(See the arrowhead symbol).  
3
 
REPLACING THE CAR DOME LAMP  
Follow the directions show below for a new lamp changing.  
1. Position light switch to “ ”.  
2. Push back the lamp cover and open it. (Refer to the following figure)  
3. Remove and discard the old lamp.  
4. Install a new bulb.  
5. Close the cover.  
Lamp Cover  
Bulb  
Light Switch  
Bulb Specification  
Diameter:  
Length:  
ø8mm  
28mm  
Voltage Spec.: DC12V, 5W  
CAR DOME LAMP WIRING  
Line for Car Dome Lamp  
Note:  
Color  
Red  
Connection  
Power Supply  
White Interior Light Supply  
Black Ground  
4
 
CONTROL & FUNCTION KEYS  
1
2
4
5
6
3
7
8
9
11  
11  
12  
12  
13  
14  
18 15 16 19 17  
5
 
CONTROL & FUNCTION KEYS  
10  
6.4 INCH TFT COLOR MONITOR  
6
 
MONITOR  
1.  
(=POWER)  
Press button (1) to turn on the unit. Press it again to turn it off.  
2. POWER INDICATOR LIGHT  
When the system is on, the indicator light (2) will be illuminated.  
3. CAR DOME LAMP  
The car dome lamp (3) will be on in some needed situations.  
4. LIGHT SWITCH  
The are three seetings for the car dome lamp operation: (OFF), (AUTO), and  
(ON), refer to light switch (4).  
A.  
B.  
C.  
: To turn off the lamp.  
: To make the lamp turned on only when car doors are opened.  
: To turn on the lamp.  
5. REMOTE SENSOR  
Point the remote control handset to the remote sensor (5).  
Press the function keys on the handset to control the unit, it would be worked for  
connecting the TV unit or DVD only.  
6. SPEAKER VOLUME CONTROL KNOB  
Rotate the knob (6) clockwise or counter-clockwise to increase or decrease the  
volume level of the speakerson the base of the unit. When rotate the knob in the  
direction of volume decresing to the end, it will turn off the speakers.  
7. BRIGHT (  
)
Rotate the bright knob (7) clockwise or counter-clockwise to increase or decrease  
the screen brightness.  
8. CONTRAST (  
)
Rotate the volume knob (8) clockwise or counter-clockwis to increase or decrease  
the contrast lever of the screen display.  
9. COLOR (  
)
Rotate the color knob (9) clockwise or counter-clockwis to increase or decrease  
the color lever of the screen display.  
10. TFT LIQUID CRYSTAL DISPLAY  
The 6.4 - inch color TFT LCD (10) can show the current state of the unit.  
11. EARPHONE VOLUME CONTROL KNOB  
Slide the knob (11) will change the volume of the earphone.  
12. JACKS FOR EARPHONE  
There are two jacks (12) for earphone. You can connect earphone to any one of  
the jacks to receive sound signal.  
7
 
13. PUSH (Monitor Release Button)  
Opening the Monitor  
Press the PUSH button (13) to eject the screen display from the base at a little  
angle. Then you can easily turn the display upward or downward for good  
viewing. The monitor also can be adjusted through 30 degree both left and right  
from the central viewing position  
Closing the Monitor  
Return the monitor to the central viewing position. Then push the monitor back  
into the monitor base unit until the screen engages with PUSH button (13) .  
14. DISPLAY DIRECTION CONTROL SWITCH  
The switch (14) should be dialed to DWN side or UP side to adjust the direction  
of the picture display and get user's needed viewing effect.  
15. DC 12V INPUT  
Through this jack (15), provide DC 12V power supply to the unit.  
16. SENSOR  
When connect DVD unit or another unit to the monitor through these two jacks  
(16), you can control the DVD unit or another unit by pointing the remote contorl  
handset directly to the remote sensor (5).  
17. AV1 IN  
The group of jacks (17) is used for AUDIO R in anf AUDIO L in and VIDEO in.  
18. AV2 IN  
The group of jacks (18) is also used for AUDIO R in anf AUDIO L in and VIDEO in.  
19. AV SELECT SWITCH  
Slide the switch (19) to 1side, the AV1 IN (17) group is avaliable; slide the  
switch (19) to 2side, AV2 IN (18) group is avaliable.  
88-T1341-03  
8
 

Pentair Swimming Pool Pump WhisperFlo User Manual
Philips Battery Charger 1235NB User Manual
Philips DVD Recorder 7819901519 User Manual
Philips Headphones SBA220 37 User Manual
Philips Headphones SHC8585 00 User Manual
Philips Portable Speaker SBD4000 27 User Manual
Pioneer Home Theater System V2550BU User Manual
Poulan Chainsaw 530163652 User Manual
Poulan Snow Blower PP7527ES User Manual
Presonus Audio electronic Music Mixer FireStudio LightPipe User Manual