PYLE Audio Car Video System PL2DNTV7 User Manual

2-DIN TFT-LCD Monitor with TV/Radio tuner  
PL2DNTV7  
Owner’s manual  
Please read it before using this equipment.  
 
WELCOME  
Thank you for purchasing the TFT-LCD wide screen MONITOR.  
We are grateful for your support.  
Please read this user’s manual in its entirety before operating the unit.  
After reading this manual, be sure to keep it in a handy place for future reference.  
Check the contents of the enclosed warranty card and keep it carefully with this manual.  
FEATURES  
7” Wide-Screen Display Panel  
Auto Switch NTSC and PAL  
High Brightness: 450 cd/m²  
Telephone Mute Control  
Headlight Control  
Auto Radio Antenna Control  
Password Protection  
Adjustable Color/Contrast/Brightness/Tint  
IR Remote Control  
On Screen Display  
AM/FM Radio Tuner  
Radio Data System (RDS)  
4 Channels x 40Watt Amplifier  
SANYO DVD/VCD/CD Changer Control  
Support RGB Input  
3 RCA Video Input (for Rear View Camera, DVD changer and AUX)  
2 RCA Stereo Audio Input  
1 RCA Video Output  
4 Channels Line-Out  
General Specifications  
Power Source:  
Car Battery (DC 9-16V)  
DC 12V  
< 1A (Typical)  
Operating Voltage:  
Operating Current:  
Operating Temperature:  
0
to 70  
Storage Temperature:  
Dimensions:  
-30°C to 80°C  
L178 x W100 x H154mm  
*Specifications and design are subject to change without notice.  
OPERATING INSTRUCTIONS  
Please read all of these instructions regarding your LCD headrest and retain them for future  
reference.  
1. Read this manual fully and carefully before operating the unit.  
1
 
2. Keep this manual handy for future reference.  
3. Pay close attention to all warnings in this manual and follow the instructions carefully.  
4. Never allow others to use the system until they have read and understood the operation  
instructions.  
SAFETY PRECAUTIONS  
1.The unit is designed for using in DC12V, negative ground battery.  
2. Do not disassemble or alter the unit in any way. Failure to do so can cause damage to the  
unit and invalidate your warranty.  
3. Be careful not to run down the car battery while using the unit with the car engine stopped.  
4. Never clean the surface of the screen with chemical solvent or corrosive detergent, which  
may cause permanent damage to TFT LCD screen.  
5. Please note that the normal working temperature of the unit is between 0to 50. If the  
internal temperature of the vehicle is extremely high, a short cooling down period is  
necessary before operating the unit.  
6. If the inside of the car is very cold and the monitor is used soon after switch on the heater,  
moisture may form on the unit. Turn off the unit immediately! Failure to do so may cause the  
internal components to short. Allow the unit to rest for about one hour to allow the  
condensation to disappear before continue operation.  
7. In extremely cold temperatures, the movement of the picture may be slow and the picture  
may be dark .It is not a malfunction .The unit will work normally once it reaches its operating  
temperature.  
8. Small black and shiny dots inside the liquid crystal panel are normal for liquid crystal panel  
are normal for liquid crystal product.  
9. Do not drop or hit the LCD panel with a hard object, as it may cause permanent damage to  
the LCD panel .If you come into contact with the fluid, do flush and clean effect areas with  
plenty of water and seek medical attention immediately.  
10. Kindly refer to authorized dealers if you get any questions.  
DISPLAY CARE & CLEANING  
Wipe off dust gently with a soft, dry cloth.  
Avoid scratching: do not rub the display with hard objects.  
Do not use any chemical solvent, cleaning agent or corrosive detergent to clean the  
display and unit.  
2
 
CAUTION! The material of display area is made by glass with a protector film attached  
on it. Do not use hard or sharp objects to strike or scratch the surface of the display  
area. Otherwise it may cause the picture distorted or have scars forever.  
Remote Control Button Functions  
1. Power  
Turn on or off this unit.  
2. Setup  
(1) DVD/CD changer mode  
DVD built-in functions menu (refer to SANYO  
DVD/CD changer Specification)  
3. Up/Down  
(1) DVD changer mode  
It is the up/down button under Setup/Menu  
status.  
Press and hold this button to choose the  
Previous/Next disc.  
(2) TV mode  
To choose the previous/next pre-set station  
4. SEL (Selection)  
(1) Press this button, to select  
a. Initial volume setup  
b. TA volume setup  
c. Bass adjustment(use VOL+/- to adjust)  
d. Treble adjustment(use VOL+/- to adjust)  
e. Balance adjustment(use VOL+/- to adjust)  
f. Fader adjustment (use VOL+/- to adjust)  
(2) Push and hold this button to select  
a. Loud on/off  
5. Enter  
(1) under DVD menu state, to confirm your selected item.  
(2) TV mode, press this button to affirm after input 0~9.  
6. Left / Right  
When startup the Setup/Menu/P. Menu function, to reduce/increase the system value or  
choose in the left/right direction.  
3
 
7. Scan /RDM  
(1) DVD/CD changer mode  
Press this button to switch scan on/off,  
Press and hold to switch random on/off.  
(2) Radio mode  
Press this button to scan any available frequency and play each one in 5 seconds.  
*During playing, will play the current frequency if you press this button again; if press  
other button, will stop this function and play the frequency at beginning of scan.  
*During scanning, will stop scanning function and play the frequency at beginning of scan.  
8. Previous/Next  
(1) Under DVD/CD changer mode  
Press this button to select the previous chapter/track or the next chapter/track;  
Press and hold this button to fast forward or fast reverse.  
(2) Under TV/Radio mode  
Press this button to search by step or fine tune;  
Press and hold this button to automatically search the previous station or the next station.  
9. Play/Pause  
(1) Under DVD/CD changer mode, to pause the playback or resume the playback.  
10. P. Menu  
(1) TFT-LCD display: picture adjustment (Brightness, Color, Contrast, Tint),  
and select PAL/NTSC/AUTO.  
(2) Including all functions on the SEL button.  
11. P. Mode  
TFT-LCD Display mode (Full, Normal).  
12. H. Angle  
It’s not available.  
13. P. Power  
It’s not available.  
14. Source  
(1) To select the mode in the following order:  
Radio > TV > DVD > AUX IN > RGB IN > Radio  
* The original mode is Radio mode.  
15. Mute  
mute on/off.  
16. Menu/Band  
(1) CDC mode  
Return to the DVD main menu during playing DVD media.  
4
 
(2) Radio mode  
To switch the band in the follows order:  
FM1 > FM2 > FM3 > MW1 > MW2  
press and hold this button to automatically search all stations and store the stations on  
band FM3 or MW2.  
17. Audio CH  
Select Tone:  
JAZZ-ROCK-CLASSIC-POP-VOCAL-FLAT-EQ OFF.  
18. VOL+ / -  
To increase volume or reduce volume.  
19. PBC/LOC  
(1) CDC mode  
To select play mode: PBC on/PCB off.  
(2) Radio mode  
As PS function, to scan all pre-set station of the current band (M1~M6, step: 5seconds).  
20. Stop  
(1) CDC mode  
To stop playback.  
21. Audio  
(1) CDC mode,  
To select audio language when playing DVD disc.  
(2) Radio mode  
To select stereo / mono  
22. Title  
Under CDC mode, to display DVD title during playing DVD media.  
23. Sub-Title  
Under CDC mode, to select sub-title language during playing DVD media.  
24. Angle  
It’s only available when playing DVD disc, which recorded some pictures from different  
angles. Press it to select from different filming angles stored on the DVD media during  
playback.  
25. Go to  
Under CDC mode, to select playtime and desired chapter.  
26. Slow  
It is not available.  
5
 
27. RPT  
Under DVD mode, allows the user to repeat playback:  
repeat mode: disc, track/chapter  
28. Angle + / -  
It is not available.  
USING REMOTE CONTROL  
Aim the IR remote control directly at the unit, or video source with an IR input.  
Tips:  
Maximum IR distance is 3 meters from the sensor.  
Direct sunlight or very bright light reduces sensitivity to the IR remote signal commands.  
Make sure the monitor is not located in direct sunlight.  
Obstruction between the remote sensor and remote control may disrupt reception.  
BATTERY  
If the remote control does not function the operating range is shortened, please change to a  
new battery.  
1. Pull out the battery holder.  
Follow the arrow 1 slide it to the right toward the battery  
while at the same time pull the battery holder away from the  
remote control.  
2. Insert a new battery with the (+) side up. (The type of battery:  
Crd2025).  
3. Push to close the holder.  
You will hear a small clicks as the tray locks.  
Batteries contain chemical substances, so they should be disposed of properly.  
Tips:  
Remove batteries if they are empty or if the remote control will not be  
used for a long time.  
Battery and small parts can be a choking hazard. Keep the remote control away from  
young children.  
6
 
Front panel Button contro  
l
1. Remote sensor  
2. Power ON/OFF ( )  
3. Mode  
4. Next/Down (  
)
5. Previous/ UP (  
)
6. Play / Pause ( )  
7. CDC  
8. Menu ( )  
9. Volume +/- or adjustment  
1) Remote sensor  
For remote control.  
2) Power on/off  
Press this power switch, the LCD monitor will turn on. Press again; the monitor will  
turn to “Mute on/off” mode. Press and hold for 3 seconds, the monitor will turn off.  
3) Mode  
Select the input signal source.  
Radio > TV > DVD >AUX IN >RGB IN > Radio  
4) Next / Down (  
)
1.Press this button to select the item down under menu state.  
7
 
2.Press this button to select the next track/chapter when playing disc under DVD  
mode, and hold to fast forward until you release it.  
3.To select the Next preset station under Radio mode.  
4.To fine the current program under TV mode.  
5) Previous / UP (  
)
1.Press this button to select the item up under menu state.  
2.Press this button to select the previous track/chapter when playing disc under DVD  
mode, and hold to fast backward until you release it.  
3.To select the previous preset station under Radio mode.  
4.To fine the current program under TV mode.  
6) Play /Pause ( )  
1.To play or pause the playback when playing disc.  
2.under Radio and TV mode, press it to auto search stations and auto store them in  
memory.  
7) CDC  
To directly select the DVD mode.  
8) Menu ( )  
Press it to setup initial volume, TA VOL, BASS, TREBLE, BALANCE, FADER.  
Hold it to enter the system menu, and you can use [ ] and [ ] to select the item  
you like to adjust, and then use [- /+] to adjust the system value.  
9) VOL - /+ or adjustment  
Press it to reduce or increase the volume.  
Press it under menu state to adjust the system value.  
8
 
Basic Operation  
System adjustment  
Press [MODE] to change the mode from AUX IN, RGB IN, REAR VIEW, RADIO MODE, TV  
MODE and DVD MODE.  
AUX IN  
It will display “NO SIGNAL” when there is no AUX in.  
RGB IN  
It will display “NO SIGNAL” when there is no RGB in.  
REAR VIEW  
It will display “NO SIGNAL” when there is no rear view in.  
RADIO MODE  
When you enter radio mode, it will display as below:  
RADIO  
BAND  
INFORMATION  
FM1  
RREQ  
CHANNEL  
87.5MHZ  
PRESET 6  
PS  
PTY  
NONE  
TA/AF/PTY/REG/EON  
LISTENING  
It will display “STERED” behind “LISTENING” when broadcasting a program.  
When you select band of “MW1” or “MW2”, “TA/AF/PTY/REG/EON” will not display on the  
above list.  
Select stations  
Press and hold [ ] or [ ] for 3 seconds to automatically search stations in the related band  
(such as FM1), and will automatically store the stations of strongest signal in related band; or  
press and hold [ ] for 3 seconds to search stations automatically and then will automatically  
store 6 stations of strongest signal in FM3.  
Value adjustment  
Press [ ] repeatedly to change from Volume >TA VOL >Bass>Treble>Balance>Fader. You  
can change the value of these five items by pressing [+] and [-].  
Press and hold [ ] to activate the system menu.  
BUZZER MODE -------500Hz  
DISP MODE ------------FULL  
PASSWORD------------OFF  
9
 
DISP TIME --------------OFF  
ADJ TIME ---------------00:25  
RADIO AREA ----------EUROPE  
TV SYSTEM ------------C.C.I.R  
EXIT  
And then, press [ ] again; it will display another page as below:  
RDS  
RDS  
RDS  
TA/TP ------------------OFF  
AF-----------------------OFF  
PTY ---------------------OFF  
SEARCH PTY -----------------NEWS  
RDS  
RDS  
EXIT  
REG--------------------OFF  
EON--------------------ON  
You can adjust the values by pressing [ ] and [ ] as below in case of entering the related  
page.  
BUZZER MODE: Select Off, 500Hz, 1KHz, 2KHz  
DISP MODE: Select the Display mode: FULL NORMAL  
PASSWORD: Password protection, select On/ Off  
DISP TIME: Display current time, select On/Off  
ADJ TIME: Time adjustment  
RADIO AREA: Select the radio area: EUROPE, China, U.S.A, TAIWAN  
TV SYSTEM: Select the TV system, C.C.I.R, U.S.A, China, Italy, Australia.  
EXIT: To exit adjustment of this page  
RDS  
RDS  
RDS  
TA/TP: Selecting OFF or ON  
AF: Selecting OFF or ON  
PTY: Selecting OFF or ON  
SEARCH PTY: Selecting from  
News>Affairs>Info>Sport>Educate>Drama>Culture>Science>Varied>  
Pop M>Rock M>Easy M>Light M>Classics>Other M  
>Weather>Finance>Children>Social>Religion>Phone in  
>Travel>Leisure>Jazz>Country>Nation M>Oldies>Folk M  
>Document>Test>Alarm.  
RDS  
RDS  
REG: Selecting OFF or ON  
EON: Selecting OFF or ON  
EXIT: To exit adjustment of this page  
Band change  
You can change the bands from FM1, FM2, FM3, MW1 and MW2 by pressing [ ] repeatedly.  
EQ adjustment  
Press [ ] repeatedly when there is playing a program to change from Volume, TA VOL,  
Bass, Treble, Balance or Fader. And then press [+] and [-] to adjust the value of related EQ  
option above.  
10  
 
TV MODE  
Select stations  
Press and hold [ ] or [ ] for 3 seconds to automatically search stations and it will  
automatically store the stations of strongest signal in related band; or press and hold [ ] for  
3 seconds to search stations automatically and then it will automatically store stations of  
strongest signal.  
If you want to stop searching, press and hold [ ] for 3 seconds again.  
Select the display mode FULL or NORMAL with menu.  
Display  
Display  
Note  
Mode  
Input video signals 16:9 picture is fully  
displayed on screen.  
Full  
When 4:3 picture is played on wide  
screen, black bands appear on both side  
of the picture.  
Normal  
Picture adjustment  
Press and hold [ ] to active the menu when there are some pictures on display.  
You can use [ ] and [ ] to select the item you would like to adjust, and then use [-/+]  
to adjust it.  
COLOR ---------------------18  
CONTRAST----------------18  
BRIGHTNESS-------------18  
TINT--------------------------18  
NTSC PAL -----------------AUTO  
RESET  
EXIT  
COLOR: Color adjustment  
CONTRAST: Contrast adjustment  
BRIGHTNESS: Brightness setting  
TINT: Adjustment to color saturation  
NTSC PAL: Select NTSC, PAL or AUTO format  
RESET: Reset above menu to default value  
EXIT: exit the menu  
11  
 
EQ adjustment  
Press [ ] repeatedly when there are some pictures on display to change from Volume, TA  
VOL, Bass, Treble, Balance or Fader. And then press [+] and [-] to adjust the value of related  
EQ option above.  
CDC MODE  
When you select CDC mode, it will display as below:  
CDC  
INFORMATION  
DISC No.:  
TRACK No.:  
PLAY TIME:  
PLAY MODE:  
01  
01  
00:00  
Repeat  
Intro  
OFF  
OFF  
OFF  
Random  
DISC PLAY  
STATUS  
Note: When it is playing a disc, it will display “DISC PLAY” behind “STATUS” on the screen,  
and when it is changing discs, it will display “DISC CHANGE” behind “STATUS” on the  
screen.  
EQ adjustment  
Press [ ] repeatedly when there is playing a program to change from Volume, TA VOL,  
Bass, Treble, Balance or Fader. And then press [+] and [-] to adjust the value of related EQ  
option above.  
Change disc  
Press and hold [ ] to change to next disc and press and hold [CDC] to change to previous  
disc.  
Select track  
You can select the desired track by pressing [ ] and [ ] repeatedly when a disc is playing.  
12  
 
Connection Layout  
Connect to your car  
1. To prevent short circuits, remove the key from the ignition and disconnected the terminal of  
the battery.  
2. Connect the wiring harness cables in the following order: ground wire, battery wire, ignition  
wire. Connect the input and output cable correctly to each unit.  
3. Connect the wiring harness connector to the monitor unit.  
13  
 
4. Reconnect the terminal of the battery of procedure.  
Notes  
If your vehicle ignition does not come with an ACC position, connect the ignition cables  
to a power source that can be turned on and turned off with the ignition key. If you  
connect the ignition cable to a power source that receives a constant voltage supply, as  
with battery cable, the battery may be overloaded.  
If the fuse blows, first check whether the cables have caused a short circuit or not, then  
replace the old fuse with a new one of the same type.  
Do not let unconnected cables or terminals touch the metal on the car of anything else  
conducting electricity. Besides, to prevent short circuits, do not remove the caps from  
unused terminals or from the ends of the unconnected cables.  
After the monitor unit is installed, please check whether the brake lamps, blinkers,  
wipers, etc…on the vehicle can work properly.  
.
Please cover unconnected cables or terminals with rubberized tape or insulators.  
Troubleshooting  
Problems  
Possible Cause  
Remedy  
No picture and  
sound when the  
monitor is turned  
on  
1. Power wire is connected  
improperly or fuse is blown.  
2. System cable isn’t  
connected or contacts  
unwell.  
1. Check the power wire  
and replace the fuse.  
2. Check the system cable  
or replace a new one.  
Blurry picture on  
the screen  
Interfered by short-distanced  
strong interference (e.g.  
motorbike, high voltage wire,  
transformation station or  
aircraft etc…)  
The reception of signal will  
get better immediately once  
leaving the interference  
area.  
No function on the 1. The battery of remote  
remote control (or control has exhausted.  
1. Change a new rating  
battery.  
operation distance 2. Remote control is destroyed. 2. Contact with the dealer  
is shortened)  
and then change a new  
remote control.  
The picture on the The equipment locates at a low This is the character of LCD  
screen is relatively temperature area.  
dark.  
monitor in low temperature,  
it will restore to normal  
brightness after powering on  
the monitor for few minutes.  
14  
 

Peerless Industries Flat Panel Television LCFL RCA27 User Manual
Pelco Webcam System 9760 User Manual
Philips Computer Drive 9305 125 20047 User Manual
Philips Headphones SHC8585 User Manual
Philips Portable CD Player AQ5050 User Manual
Philips TV VCR Combo 25PV707 User Manual
Plustek Scanner A360 User Manual
Polaris Camcorder D7500 User Manual
Poulan Trimmer 530088847 User Manual
PYLE Audio Music Mixer PEMP 8 User Manual