PYLE Audio Microphone PDWM2200 User Manual

PDWM2700  
TWO CHANNELS  
VHF WIRELESS MICROPHONE  
TRANSMITTER  
USER'S MANUAL  
 
HANDHELD MICROPHONE  
TROUBLE SHOOTING  
Please read and check the following points before asking for service.  
The wireless microphone fails fo work:  
--Check the microphone battery by switching the microphone ON. If power LED  
indicator lights red, replace the battery.  
--Check the POWER indicator on the receiver unit is ON. If not, check the  
mains power adapter is firmly plugged into a working mains socket.  
--Check the amplifier system is ON and the microphone controls set correctly.  
--Check the radio microphone jack lead is firmly connected into the output  
socket on the rear panel of the receiver unit and into the MIC input socket on  
your amplifier.  
The working range is limited:  
--Check the microphone battery condition(see above)  
--Check the aerials are fully extended. Adjust the position of the aerials to  
achieve the best reception.  
Feedback is heard:  
1. Unscrew the battery cover at the end of the microphone. Install the  
provided 9 volt battery and then close the cover. Make sure to connect  
with the correct polarity.  
--Check if the microphone is too close to or in front of the loudspeaker.  
Check the settings of the microphone controls on the amplifier. Adjust volume  
and tone to get the beat sound without any trace of feedback.  
2. Move power switch to ON position. Power LED indicator will flash  
once and then go off. This indicates correct operation. If power LED  
indicator lights red, this indicates the battery is Iow. Please replace  
with new battery.  
3. Move power switch to center to mute the microphone.  
4. If the microphone is not going to be used for a long period of time,  
please take out the battery to prevent damage by battery leakage.  
2
7
 
SPECIFICATIONS  
BELT PACK TRANSMITTER  
A. Overall system  
1. Oscillation mode:  
2. Carrier Frequency Range  
3. Frequency Stability:  
4. Max Deviation:  
Quartz controlled  
VHF160~270MHz  
+/-0.005%  
BATTERYCOVER  
9V BATTERY  
MIC IN  
+/-56KHz with level limiting  
>110dB  
5. Dynamic Range:  
6. S/N Ratio:  
POWER INDICATOR  
POWER SWITCH  
>100dB  
7. T. H. D:  
<0.5dB  
8. Frequency Response  
9. Operating Range:  
60Hz-18KHz  
30M  
OPEN  
CLOSE  
B. Receiver  
1. Sensitivity:  
6dB V at SIN >70dB  
>60dB  
2. Image Rejection:  
3. Stability:  
>80dB  
4. Audio output:  
5. Power supply:  
-12db/600ohm unbalanced  
12V DC/500mA  
LAVALIER MIC  
HEADSET MIC  
C. Transmitter  
1. Mike capsule:  
Handheld: dynamic  
Headset or lavalier MIC: condenser  
Built-in housing(Handheld MIC)  
external(Belt pack)  
<10mW  
1. Open the battery cover to install a 9V battery as per correct  
polarities.  
2. Antenna:  
2.Move power switch to ON position. Power LED indicator will  
flash once and then go off. This indicates correct operation. If  
power LED indicator lights red, this indicates the battery is  
Iow. Please replace with new battery.  
3. RF Output:  
4. Spurious:  
<-40dBC  
5. Power Supply:  
9V battery  
3. Plug the 3.5mm connector of headset mic to MIC in jack of  
transmitter.  
4. Before operation, please confirm that the frequency of  
transmitter is same as the frequency of receiver.  
5. When speak to the MIC, please keep 2-3cm distance between  
mouth and mic head.  
6. If the system will not be used for a long time, please take out  
battery from transmitter to avoid damage by battery leakage.  
6
3
 
RECEIVER  
INSTALLATION  
To connect the wireless microphone to your amplifier system:  
Refer to the installation diagram below.  
Using the supplied 6.35mm to 6.35mm lead, connect from the AF  
OUT jack of the receiver to the MIC INPUT socket on your amplifier.  
Plug one end of the mains power adapter into a suitable mains socket.  
Plug the other end of the adapter into receiver DC 12V input socket.  
CHA SIGNAL  
CHB SIGNAL  
1. Switch on the wireless microphone receiver unit by pressing the POWER  
switch and the POWER light will illuminate to show the receiver unit is  
working.  
2. Fully extend the aerials to the maximum height.  
3. Switch ON the transmitter. Power LED indicator will flash once then go off.  
When the microphone is ON, the receiver RF indicator will light.  
4. Adjust the volume and tone levels of your amplifier system as well as the  
receiver & the body pack as required.  
5. When the transmitter is not going to be used for a long period of time,  
please take out the battery from transmitter.  
Note that switching the microphone on and off can cause interference that  
will be heard if the microphone volume level of the amplifier system is still  
set high  
4
5
 

Pelco Home Security System C1456M D User Manual
Pelco Home Security System C3447M B 8 09 User Manual
Philips Computer Drive SPE9000CC User Manual
Philips Iron GC3500 User Manual
Philips Kitchen Grill HD2383 User Manual
Philips Network Card SDJ6120W User Manual
Pioneer Car Video System DVH P7050 User Manual
Polaroid Video Games TDX 142 User Manual
Pride Mobility Mobility Aid Jazzy 1170XL User Manual
Princeton VCR 4411 0118 User Manual