SD5-P
Metal Ceiling Panel
C1459M-B (2/03)
®
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Installation and servicing should be done only by qualified service personnel and
conform to all local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P
enclosure, it is designed for indoor use only and it must not be installed where
exposed to rain and moisture.
3. The installation method and materials should be capable of supporting four times
the weight of the unit and equipment.
4. Only use replacement parts recommended by Pelco.
DESCRIPTION
The SD5-P metal ceiling panel is designed for use with Spectra Series in-ceiling back box and DF5 in-ceiling fixed-mount domes. The metal ceiling
panel can be used to replace or reinforce the 2' x 2' ceiling tile in suspended ceiling installations.
The following parts are supplied:
Qty.
1
4
Description
2’ x 2’ metal panel
T-rail clip
Pelco World Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com
USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150
International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120
REINFORCEMENT INSTALLATION
1. Remove the ceiling tile from the ceiling.
2. Prepare the ceiling tile for installation. Use the metal panel as a template. Place the metal panel on top of the ceiling tile, and draw an outline
of the center circle. Cut the circle out of the ceiling tile.
3. Remove the conduit fitting, lock nut, and safety chain bracket from the parts bag that came with the back box, and attach them to the back box
as shown in Figure 1.
4. Place the metal panel on top of the ceiling tile.
NOTE: When installed, the metal panel will be inside the ceiling with the ceiling tile exposed.
5. Install the back box in the ceiling tile and metal panel by compressing the spring clips and pushing the back box through the hole. Tighten the
screws until you hear a clicking noise.
6. Install the tile and panel in the ceiling.
7. Use the T-brackets and clips supplied with the back box to attach a T-bracket and clip on each side of the metal panel as shown in Figure 3.
T-BRACKET
AND CLIP
METAL PANEL
CEILING TILE
Figure 3. T-Bracket and Clip Installation
8. Install a safety chain/cable (not supplied) that will support up to 16 pounds (7.3 kg). Fasten one end of the chain/cable to a support structure in
the ceiling. Fasten the other end to the safety chain bracket (refer to Figure 1).
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment. Exceptions to this warranty are
as noted below:
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to
obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600
Series); two years on all other cameras.
Three years on Genex® Series (multiplexers, server, and keyboard) and 090 Series Camclosure®
Camera System.
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product when returned.
•
•
•
Two years on 100/150, 200 and 300 Series Camclosure® Camera Systems.
Two years on cameras and all standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM6800E/CM8500/CM9500/CM9740/CM9760
Matrix, DF5 and DF8 Series Fixed Dome products.
Method of return shipment shall be the same or equal to the method by which the item was received by
Pelco.
•
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous
motion applications.
RETURNS
•
•
•
Two years on Esprit and WW5700 series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders.
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100
or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if
returned for repair).
•
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applica-
tions (that is, preset scan, tour and auto scan modes).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and
freight should be prepaid. Ship to the appropriate address below.
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:
Service Department
Pelco
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no
event will Pelco be liable for any special, incidental or consequential damages (including loss of
use, loss of profit and claims of third parties) however caused, whether by the negligence of
Pelco or otherwise.
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:
Intermediate Consignee
American Overseas Air Freight
320 Beach Road
Burlingame, CA 94010
USA
Ultimate Consignee
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
USA
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
REVISION HISTORY
Manual #
C1459M
C1459M-A
C1459M-B
Date
3/97
2/98
2/03
Comments
Original version.
Revised to include usage with DFSS Series shortened back box.
Revised to include Spectra III SE and Spectra III back box models. Updated manual to new format.
® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco.
© Copyright 2003, Pelco. All rights reserved.
|