Pelco Home Security System PMVR2 User Manual

Q U I C K S T A R T G U I D E  
PMVC4/PMVR2  
Multiviewer  
Multiple Image Display System  
C2929M (5/06)  
 
CONNECTING MULTIPLE PMVC4 UNITS  
Remember, when cascading PMVC4s, loop from the multiviewer with a lower ID to the multiviewer with a higher ID. Also, the following  
additional steps are required when connecting multiple units.  
1. Use a flat head screwdriver on the rotary Unit ID switch to set the ID of the first multiviewer in the display group to 0. This identifies it in the  
software as the first multiviewer. Change the ID of every additional multiviewer in the group by increments of one; for example, the next  
multiviewer will have an ID of 1. Do not use F, which is for testing only.  
2. Connect a 10-inch (25.4-centimeter) DB9 serial cable from COM OUT on unit 0 to COM IN on the next unit, which is unit 1. Repeat until you  
reach the last unit in the group.  
3. Connect a DVI looping cable from Cascade/In on unit 0 to Cascade/DVI Out on the next unit, which is unit 1. Repeat until you reach the last  
unit in the group.  
DISPLAY  
MONITOR  
PC AND CONTROL  
MONITOR  
CAMERAS  
VGA OR DVI  
OUTPUT  
VGA Out  
Video 1  
Video 2  
Video 3  
Video 4  
COM IN  
4
C
COM OUT  
Cascade In  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
PMVC4 ID0  
CAMERAS  
VGA Out  
Video 1  
Video 2  
Video 3  
Video 4  
COM IN  
4
C
COM OUT  
Cascade In  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
PMVC4 ID1  
Figure 3. Connecting Multiple PMVC4s  
CONNECTING A SINGLE PMVR2  
1. Connect any DVI inputs (such as from a VMX300 video management system) to the DVI 1 and 2 connectors or any VGA inputs (such as from  
a DX8000 series digital video recorder) to the VGA 1 and 2 connectors on the back of the PMVR2.  
NOTE: You can have either DVI or VGA, but not both on the same channel. However, you can have DVI and VGA if you put them on  
different channels; for example, DVI on DVI 1 and VGA on VGA 2.  
2. Connect the male end of the 6-foot (1.8-meter) DB9 serial cable to COM IN on the PMVC4. Connect the other end (with the RS-232-to-  
RS-485 converter) to the PC’s COM port.  
3. Connect either a DVI looping cable from Cascade/DVI Out or a VGA looping cable from VGA Out to the display monitor.  
C2929M (5/06)  
3
 
PC AND CONTROL  
MONITOR  
DISPLAY  
MONITOR  
VMX300  
DX8000  
VGA  
OR DVI  
OUTPUT  
VGA 1  
VGA 2  
DVI 1  
DVI 2  
ON  
OFF  
COM IN  
4
C
COM OUT  
Cascade In  
VGA Out  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
PMVR2  
Figure 4. Connecting a Single PMVR2  
CONNECTING MULTIPLE PMVR2 UNITS  
Remember, when cascading PMVR2s, loop from the multiviewer with a lower ID to the multiviewer with a higher ID. Also, the following  
additional steps are required when connecting multiple units.  
1. Use a flat head screwdriver on the rotary Unit ID switch to set the ID of the first multiviewer in the display group to 0. This identifies it in the  
software as the first multiviewer. Change the ID of every additional multiviewer in the group by increments of one; for example, the next  
multiviewer will have an ID of 1. Do not use F, which is for testing only.  
2. Connect any DVI inputs (such as from a VMX300 video management system) to the DVI 1 and 2 connectors or any VGA inputs (such as from  
a DX8000 series digital video recorder) to the VGA 1 and 2 connectors on the back of the PMVR2.  
3. Connect a 10-inch (25.4-centimeter) DB9 serial cable from COM OUT on unit 0 to COM IN on the next unit, which is unit 1. Repeat until you  
reach the last unit in the group.  
4. Connect a DVI looping cable from Cascade/In on unit 0 to Cascade/DVI Out on the next unit, which is unit 1. Repeat until you reach the last  
unit in the group.  
DISPLAY  
MONITOR  
VMX300  
PC AND CONTROL  
MONITOR  
DX8000  
VGA  
OR DVI  
OUTPUT  
VGA 1  
VGA 2  
DVI 1  
DVI 2  
COM IN  
4
C
COM OUT  
Cascade In  
VGA Out  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
PMVR2 ID0  
DX8000  
DX8000  
VGA 1  
VGA 2  
DVI 1  
DVI 2  
COM IN  
4
C
COM OUT  
Cascade In  
VGA Out  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
PMVR2 ID1  
Figure 5. Connecting Multiple PMVR2s  
4
C2929M (5/06)  
 
CONNECTING BOTH PMVC4 AND PMVR2 UNITS  
In cascading PMVC4 multiviewers with PMVR2 multiviewers, remember to loop from a multiviewer with the lower ID to a multiviewer with a  
higher ID. Begin with PMVC4 multiviewers and then PMVR2 multiviewers. Follow the instructions for connecting multiple units.  
DISPLAY  
MONITOR  
PC AND CONTROL  
MONITOR  
VGA OR DVI  
OUTPUT  
CAMERAS  
PMVC4 ID0  
VGA Out  
Video 1  
Video 2  
Video 3  
Video 4  
COM IN  
4
C
COM OUT  
Cascade In  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
CAMERAS  
PMVC4 ID1  
VGA Out  
Video 1  
Video 2  
Video 3  
Video 4  
COM IN  
4
C
COM OUT  
Cascade In  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
VMX300  
DX8000  
PMVR2 ID2  
VGA 1  
VGA 2  
DVI 1  
DVI 2  
COM IN  
4
C
COM OUT  
Cascade In  
VGA Out  
Unit ID  
100-240 VAC  
Cascade/DVI Out  
Figure 6. Connecting PMVC4s and a PMVR2  
Step 2: Installing the Manager Software  
1. Insert the resource CD in your PC. A splash screen appears.  
2. Click in the splash screen. The program will be extracted into a folder, and a shortcut called Pelco Multiviewer Manager will be added to  
the desktop.  
3. Locate the Pelco Multiviewer Manager shortcut on the desktop. Click it to launch the application. The program displays the Scan All Online  
Modules dialog box.  
Click Next. If the software does not find anything, it will not let you go further. Click Rescan in this situation to make sure the software can  
detect all your multiviewers.  
C2929M (5/06)  
5
 
4. The program displays the Set Total Monitor dialog box, which determines how many display groups you have.  
Figure 7. Set Total Monitor Dialog Box  
Set the number of monitors (up to 50 monitors). You must set this first.  
If you click the Auto Set check box, the program will quickly set up a single group or multiple groups. (If you do not click the Auto Set  
check box, the program will bypass steps 6 and 7. Skip the following instructions and go directly to Step 8.)  
Choose either to have one multiviewer per group or all multiviewers in one group. Pick the resolution you want. Select the space  
between windows, and then click the Open MCC Label check box.  
Click Back to return or Next to continue.  
5. The program displays the Set Up All Groups dialog box, which shows the monitor and group for that monitor.  
Figure 8. Set Up All Groups Dialog Box  
Leave the No VGA Overlay box checked in the Attach VGA Monitor section. Select the output resolution.  
Select the multiviewers you want to include in the group by clicking their checkboxes. Use the Include and Remove buttons to  
add/remove the desired multiviewers.  
Click Back to return or Next to continue. When you complete the last monitor, click Back to return to the monitor or Finish to continue.  
6. The program displays the Report dialog box, which confirms the selected multiviewers and their identifications (IDs). The Report dialog box  
also indicates whether a VGA monitor is attached and the number of multiviewers (modules) in the group. Click Cancel or OK.  
6
C2929M (5/06)  
 
7. The program next displays the Set Monitor Type dialog box. The settings in this dialog box are optional. They are only a graphic  
representation of the system and do not actually affect the system itself.  
Figure 9. Set Monitor Type Dialog Box  
Select the group.  
Use the zoom buttons to decrease or increase the image on the control screen.  
Select values for ratio and size. Click the Apply All check box to apply the ratio settings to all the images.  
Use the horizontal and vertical menus to quickly organize multiple group display icons. This feature lets you set up a global view of  
your system to see where each group display is located. Click the SET button.  
Click Cancel or OK.  
8. The program displays the Pelco Monitor Manager window (refer to Figure 10). Software installation is complete.  
NOTE: If you need to modify some of the settings after the initial installation, you must exit the program, access Windows Explorer, locate the  
Pelco Multiviewer Manager program file, delete the Save file, and begin again.  
Step 3: Configuring the Equipment  
PELCO MULTIVIEWER MANAGER SOFTWARE  
The Pelco Multiviewer Manager (PMM) software is required to configure and control the multiviewers. This included program gives you access  
to system level commands, group level commands, and window level commands through the Pelco Monitor Manager window.  
Use the pull-down menu to select between system level (overview) or group level control.  
COMMAND AREAS  
System Level and Group Level: These menus (File, Program, and Tools) display system level and group level commands. System level  
commands are program features that make system-wide changes. Group level commands affect only the group currently being controlled.  
Group Level Only: These menus only display group level commands. Access these by right-clicking the mouse while the cursor is in the  
black background area, outside a video window.  
Window Level Only: These menus only display commands at the video window level. Access these by right-clicking the mouse while the  
cursor is in a video window. Window level commands affect the selected video window only.  
For detailed information on configuring the equipment, refer to the manual on the included resource CD.  
C2929M (5/06)  
7
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted  
pair transmission products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.  
The lamp and color wheel will be covered for a period of 90 days. The air filter is not  
covered under warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelco’s liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
Date  
Comments  
C2929M  
5/06  
Original version.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2006, Pelco. All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc.  
Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com  
USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150  
International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120  
 

Peavey Microphone PVM 48 User Manual
Philips Baby Monitor SCD588 54 User Manual
Philips Computer Monitor 107H67 User Manual
Philips Home Safety Product SBCFL121 User Manual
Philips Microcassette Recorder LFH0620 User Manual
Pixel Magic Systems Home Theater System VPS3800 User Manual
Plasmon DVD Player D2175 User Manual
Poulan Cultivator 530164258 User Manual
Powermate Portable Generator PM052531201 User Manual
Precor Treadmill 842i User Manual