Pelco Patio Heater C1495M B User Manual

®
HKX* Series Heater  
and  
BKX* Series Blower  
for EHX*E Series  
Explosion-Proof  
Camera Enclosure  
Installation/  
Operation Manual  
C1495M-B (10/03)  
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150  
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348  
 
(This page intentionally left blank.)  
Pelco Manual C1495M-B (10/03)  
3
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should only be done by qualified service personnel and con-  
form to all local codes.  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclo-  
sure, it is designed for indoor use only and it must not be installed where exposed to  
rain and moisture.  
3. Only use replacement parts recommended by Pelco.  
4. For marine applications, the installation shall be in accordance with the Electrical Engi-  
neering Regulations of the USCG, Subpart J, C.G. 259 (46 CFR Parts 110-113).  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
C A U T I O N :  
within this unit.  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are impor-  
tant operating and maintenance instructions  
in the literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation  
and operation.  
DESCRIPTION  
The heater and blower kits described in this manual are intended to work with the EHX*E  
Series of non-pressurized, explosion-proof camera enclosures.  
When installing heater and blower kits in EHX*E Series explosion-proof camera enclosures,  
the maximum camera and lens sizes are reduced depending on the size of the blower, heater  
brackets, and PC board(s). Before installing the heater and blower kit, verify that the camera  
currently installed in the enclosure will fit in the enclosure after installation of the accessories  
(refer to the Specifications section in this manual).  
BLOWER AND HEATER KITS  
BKX4000  
BKX4024  
BKX6000  
BKX6000/220  
BKX6024  
HKX4-1  
Continuously run blower kit, 120 VAC, 3.8 watts, 10 cfm @ 60 Hz. For use  
with EHX4E enclosure only.  
Continuously run blower kit, 24 VAC (AC rectified), 1.92 watts, 19.4  
cfm. For use with EHX4E enclosure only. (CE)  
Continuously run blower kit, 120 VAC, 3.8 watts, 10 cfm @ 60 Hz. For use  
with EHX6E, EHX6E-16, EHX8E, EHX10E enclosures.  
Continuously run blower kit, 230 VAC, 9.6 watts, 8 cfm @ 50 Hz. For use  
with EHX6E, EHX6E-16, EHX8E, EHX10E enclosures. (CE)  
Continuously run blower kit, 24 VAC (AC rectified), 1.92 watts, 19.4 cfm.  
For use with EHX6E, EHX6E-16, EHX8E, EHX10E enclosures. (CE)  
Thermostatically controlled heater kit, 120 VAC, 40 watts, for EHX4E  
enclosure only.  
NOTE: Blower kits are not  
thermostatically controlled.  
HKX4-2  
HKX4-3  
HKX6-1  
Same as HKX4-1 except 24 VAC. (CE)  
Same as HKX4-1 except 230 VAC. (CE)  
Thermostatically controlled heater kit, 120 VAC, 80 watts, for EHX6E  
and EHX6E-16 enclosures only.  
HKX6-2  
Same as HKX6-1 except 24 VAC. (CE)  
HKX6-3  
Same as HKX6-1 except 230 VAC. (CE)  
HKX8/10-1  
Thermostatically controlled heater kit, 120 VAC, 100 watts, for EHX8E  
and EHX10E enclosures only.  
HKX8/10-2  
HKX8/10-3  
Same as HKX8/10-1 except 24 VAC, 40 watts. (CE)  
Same as HKX8/10-1 except 230 VAC, 100 watts. (CE)  
4
Pelco Manual C1495M-B (10/03)  
 
INSTALLATION  
HEATER KIT INSTALLATION  
The following items are supplied:  
WARNING: Do  
not remove the  
Assembly, including heater bracket, PC board bracket, heaters, and PC board  
Hardware to attach the heater and PC board brackets to the enclosure:  
front cover. If you  
do, Pelco cannot be held re-  
sponsible for the loss of ex-  
plosion-proof rating, UL list-  
ing, or ability of the enclo-  
sure to contain an explosion.  
HKX4  
HKX6 HKX8/10  
3/8-inch screws  
Nuts  
Internal tooth lock washers  
6
2
6
4
2
4
4
2
4
Heater kits are partially assembled. If you are installing both heater and blower kits, see the  
instructions in the Heater Kit and Blower Kit Installation section. Do the following to install  
any heater kit:  
1. Disconnect all sources of power from the enclosure.  
2. Remove the enclosure’s rear plate with a 5 mm Allen wrench.  
3. Remove the camera sled and camera from the enclosure.  
a. Use a 3/16-inch Allen wrench to loosen the set screw that holds the camera sled  
in place.  
b. Partially pull the camera sled out; disconnect the camera’s power wires and video  
cable.  
c. Remove the camera sled from the enclosure.  
d. Remove the camera from the sled.  
4. Disconnect the heater wires from the PC board.  
5. Attach the PC board bracket to the enclosure’s rear plate using the hardware provided  
(refer to Figure 1 or 2).  
6. Attach the heater bracket to the front of the camera sled using the hardware provided  
(refer to Figure 3 or 4).  
7. Reinstall the camera and camera sled, but do not tighten the set screw that holds the  
sled in place.  
8. Attach the video cable to the camera.  
9. Reconnect the heater wires to the PC board (refer to Figure 8).  
10. If the camera uses a different voltage than the heater, reconnect the power wires to  
the camera. If the camera uses the same voltage as the heater, proceed to the next step.  
11. Bring power wires through the rear plate and connect the wires to the PC board (refer  
to Figure 8). If you are installing the HKX4-2, HKX6-2, or HKX8/10-2 heater kit, refer to  
Table A, 24 VAC Wiring Distances. If the camera uses the same voltage as the heater,  
the camera power consumption must be considered when determining the wire gauge.  
Table A does not include camera power because of the many variations.  
12. Tighten the set screw that holds the camera sled in place.  
13. Reinstall the rear plate of the enclosure. Apply Loctite® 222 low-strength thread locker  
(not supplied) to the screws to prevent them from seizing.  
Pelco Manual C1495M-B (10/03)  
5
 
BLOWER KIT INSTALLATION  
The following items are supplied:  
Assembly, including blower and bracket.  
Hardware to attach the blower, bracket, and PC board (24 VAC only) to the enclosure:  
NOTE: The 24 VAC and the  
230 VAC versions use addi-  
tional components that should  
be secured to the fan bracket  
with the integrated clip in the  
bracket.  
BKX4000 BKX4024 BKX6000/220  
3/8-inch screws  
Internal tooth lock washers  
Nuts  
2
2
0
2
2
2
0
2
2
2
2
2
Butt splices  
Blower kits are partially assembled. If you are installing both heater and blower kits, see the  
instructions in Heater Kit and Blower Kit Installation section. Do the following to install any  
blower kit:  
1. Disconnect all sources of power from the enclosure.  
2. Remove the enclosure’s rear plate with a 5 mm Allen wrench.  
3. Attach the blower assembly to the enclosure’s rear plate using the hardware provided  
(refer to Figure 5, 6, or 7).  
4. Bring power wires through the rear plate and connect the AC input wiring to the blower  
wires with the butt splices that are provided (refer to Figure 8).  
5. Reinstall the rear plate of the enclosure. Apply Loctite® 222 low-strength thread locker  
(not supplied) to the screws to prevent them from seizing.  
6
Pelco Manual C1495M-B (10/03)  
 
HEATER KIT AND BLOWER KIT INSTALLATION  
Do the following to install both the heater and blower kits:  
1. Disconnect all sources of power from the enclosure.  
2. Remove the enclosure’s rear plate with a 5 mm Allen wrench.  
3. Remove the camera sled and camera from the enclosure.  
a. Use a 3/16-inch Allen wrench to loosen the set screw that holds the camera sled  
in place.  
b. Partially pull the camera sled out; disconnect the camera’s power wires and video  
cable.  
c. Remove the camera sled from the enclosure.  
d. Remove the camera from the sled.  
4. Disconnect the heater wires from the PC board.  
5. Remove the blower from the bracket; keep the hardware attaching the blower to the  
bracket and discard the bracket.  
6. Attach the blower to the bracket on which the PC board for the heater is attached.  
7. Attach the PC board and blower bracket to the enclosure’s rear cover the hardware  
provided (refer to Figures 1 and 2).  
8. Attach the heater bracket to the front of the camera sled using the hardware provided  
(refer to Figures 3 and 4).  
9. Reinstall the camera and sled; do not tighten the set screw that holds the sled in place.  
10. Attach the video cable to the camera.  
11. Reconnect the heater wires to the PC board (refer to Figure 8).  
12. If the camera uses a different voltage than the heater, reconnect the power wires to  
the camera. If the camera uses the same voltage as the heater, proceed to the next step.  
13. Bring power wires through the rear plate and connect the wires to the PC board (refer  
to Figure 8). If you are installing the HKX4-2, HKX6-2, or HKX8/10-2 heater kit, refer to  
Table A, 24 VAC Wiring Distances. If the camera uses the same voltage as the heater,  
the camera power consumption must be considered when determining the wire gauge.  
Table A does not include camera power because of the many variations.  
14. Tighten the set screw that holds the camera sled in place.  
15. Reinstall the rear plate of the enclosure. Apply Loctite® 222 low-strength thread locker  
(not supplied) to the screws to prevent them from seizing.  
Pelco Manual C1495M-B (10/03)  
7
 
A
B
1
2
3
C
B
A
Figure 1. HKX4 PC Board Installation  
A
B
1
2
C
3
B
A
Figure 2. HKX6, HKX8/10 PC Board Installation  
Table A. HKX4, HKX6, HKX8/10 Series PC Board Assembly Parts List  
Item  
Qty  
Description  
PC board  
Part Number  
1
2
3
1
1
1
PCB9000300ASSY  
BK400010000  
Insulator  
PC board bracket  
HKX4  
E7044012COMP  
BK40004000COMP  
HKX6, HKX8/10  
A
B
C
D
Screw, 6-32 x 3/8-inch  
HKX4  
HKX6, HKX8/10  
Internal tooth lock washer, #6  
HKX4  
HKX6, HKX8/10  
Nylon washer  
HKX4  
ZH6-32X.375SPP  
4
6
ZH6LWSIS  
4
6
ZH200X437X62N  
570010004  
2
4
1
HKX6, HKX8/10  
Brass solder lug  
(for grounding circuit board)  
8
Pelco Manual C1495M-B (10/03)  
 
A
1
B
C
Figure 3. EHX4E Heater Bracket Installation  
1
A
B
C
Figure 4. EHX6E/8E/10E Heater Bracket Installation  
Table B. HKX4, HKX6, HKX8/10 Series Heater Assembly Parts List  
Item  
Qty  
Description  
Heater Bracket  
Part Number  
1
1
HKX4 Series  
HKX6, HKX8/10 Series  
Heaters  
E7044013COMP  
E700H4010COMP  
N/S*  
2
HKX4-1, 120 VAC  
HKX4-2, 24 VAC  
HKX4-3, 230 VAC  
HKX6-1, 120 VAC  
HKX6-2, 24 VAC  
HKX6-3, 230 VAC  
HKX8/10-1, 120 VAC  
HKX8/10-2, 24 VAC  
HKX8/10-3, 230 VAC  
HT71-04040100  
HT72-04040100  
HT73-04040100  
HT07-0810-0402  
HT07-0820-0402  
HT07-0830-0402  
HTR50120  
HTR20024  
HTR40220  
A
B
C
2
2
2
Screw, 6-32 x 3/8-inch  
Internal tooth lock washer, #6  
Nut, 6-32, hex  
ZH6-32X.375SPP  
ZH6LWSIS  
ZH6-32NUTSH  
Pelco Manual C1495M-B (10/03)  
9
 
A
B
1
BKX4024 ONLY  
5
2
3
4
B
A
B
A
B
C
Figure 5. BKX4000, BKX4024 Blower Assembly Installation  
Table C. BKX4000, BKX4024 Blower Assembly Parts List  
Item  
Qty  
Description  
Blower bracket  
Blower bracket  
Blower bracket  
Blower  
Part Number  
1
2
3
4
1
1
1
1
BK7044002COMP  
E7044012COMP  
BK7044001COMP  
BKX4000, 120 VAC  
BKX4024, 24 VDC rectified  
PC Board  
MM750010003  
ED210005  
PCB9000277ASSY  
5*  
A
1
Screw, 6-32 x 3/8-inch  
BKX4000  
BKX4024  
ZH6-32X.375SPP  
6
7
B
C
Internal tooth lock washer, #6  
BKX4000  
BKX4024  
ZH6LWSIS  
7
8
1
Screw, 6-32 x 1 1/2-inch  
ZH6-32X1.50SPS  
* BKX4024 only  
10  
Pelco Manual C1495M-B (10/03)  
 
BKX6000/220 ONLY  
A
B
3
E
1
B
C
B
A
D
2
Figure 6. BKX6000, BKX6000/220 Blower Assembly Installation  
Table D. BKX6000, BKX6000/220 Blower Assembly Parts List  
Item  
Qty  
Description  
Blower bracket  
Blower  
Blower bracket  
Part Number  
1
2
3*  
1
1
1
BK40004000COMP  
MM750010003  
BK7044002COMP  
A
B
C
D
E
6
8
2
2
4
Screw, 6-32 x 3/8-inch  
Internal tooth lock washer, #6  
Screw, 6-32 x 1 1/2-inch  
Nut, 6-32, hex  
ZH6-32X.375SPP  
ZH6LWSIS  
ZH6-32X1.50SPS  
ZH6-32NUTSH  
ZH200X437X62N  
Nylon washer  
* BKX6000/220 only  
Pelco Manual C1495M-B (10/03)  
11  
 
1
B
C
B
A
3
B
D
A
BKX6024 ONLY  
D
2
Figure 7. BKX6024 Blower Assembly Installation  
Table E. BKX6024 Blower Assembly Parts List  
Item  
Qty  
Description  
Blower bracket  
Blower, 24 VDC rectified  
PC Board  
Part Number  
1
2
3
1
1
1
BK40004000COMP  
ED210005  
PCB9000277ASSY  
A
B
C
D
3
4
1
2
Screw, 6-32 x 3/8-inch  
Internal tooth lock washer, #6  
Screw, 6-32 x 1 1/2-inch  
Nut, 6-32, hex  
ZH6-32X.375SPP  
ZH6LWSIS  
ZH6-32X1.50SPS  
ZH6-32NUTSH  
12  
Pelco Manual C1495M-B (10/03)  
 
AC  
AC  
GND  
1
2
DIODE  
CAPACITOR  
RED  
BLK  
3
4
5
RED  
BLK  
AC IN  
6
7
BLOWER  
HEATER  
HEATER  
8
9
10  
BLOWER  
BUTT SPLICES  
RECTIFIER  
PC BOARD  
RECTIFIER  
PC BOARD  
HEATER ONLY OR HEATER AND BLOWER  
BLOWER ONLY  
24 VAC WIRING DIAGRAM  
AC  
AC  
GND  
1
2
3
4
5
6
7
AC IN  
BLOWER  
HEATER  
HEATER  
8
9
10  
BLOWER  
BUTT SPLICES  
HEATER ONLY OR HEATER AND BLOWER  
BLOWER ONLY  
120 VAC WIRING DIAGRAM  
AC  
AC  
GND  
1
2
3
4
5
AC IN  
6
7
8
9
BLOWER  
RESISTOR  
BLOWER  
HEATER  
HEATER  
BUTT SPLICES  
RESISTOR  
10  
HEATER ONLY OR HEATER AND BLOWER  
BLOWER ONLY  
230 VAC WIRING DIAGRAM  
Figure 8. Heater/Blower Kit Wiring Diagram  
Pelco Manual C1495M-B (10/03)  
13  
 
Table F. Enclosure Accessory Wiring Distances  
CAUTION: When a single power source is used for both the camera and accessories, the camera power con-  
sumption must be considered when determining the wire gauge. However, the following chart does not include  
camera power because of the many variations.  
Power  
Model Number  
BKX4000  
or  
Input Voltage  
Consumption  
Cable Size  
Cable Distance  
120 VAC  
4 watts  
18 AWG  
16 AWG  
14 AWG  
27,108 feet (8,262 m)  
43,062 feet (13,125 m)  
68,441 feet (20,860 m)  
BKX6000  
BKX4024  
or  
BKX6024  
24 VAC  
230 VAC  
120 VAC  
24 VAC  
2 watts  
10 watts  
40 watts  
40 watts  
40 watts  
80 watts  
80 watts  
80 watts  
100 watts  
40 watts  
100 watts  
18 AWG  
16 AWG  
14 AWG  
2,169 feet  
3,445 feet (1,050 m)  
5,475 feet (1,669 m)  
(661 m)  
BKX6000/220  
18 AWG  
16 AWG  
14 AWG  
36,446 feet (11,108 m)  
57,895 feet (17,645 m)  
92,015 feet (28,045 m)  
HKX4-1  
18 AWG  
16 AWG  
14 AWG  
2,711 feet  
4,306 feet (1,312 m)  
6,844 feet (2,086 m)  
(826 m)  
HKX4-2  
18 AWG  
16 AWG  
14 AWG  
108 feet  
172 feet  
274 feet  
(33 m)  
(52 m)  
(83 m)  
HKX4-3  
230 VAC  
120 VAC  
24 VAC  
18 AWG  
16 AWG  
14 AWG  
9,111 feet (2,777 m)  
14,474 feet (4,411 m)  
23,004 feet (7,011 m)  
HKX6-1  
18 AWG  
16 AWG  
14 AWG  
1,355 feet  
2,153 feet  
3,422 feet (1,043 m)  
(413 m)  
(656 m)  
HKX6-2  
18 AWG  
16 AWG  
14 AWG  
54 feet  
86 feet  
137 feet  
(17 m)  
(26 m)  
(42 m)  
HKX6-3  
230 VAC  
120 VAC  
24 VAC  
18 AWG  
16 AWG  
14 AWG  
4,556 feet (1,389 m)  
7,237 feet (2,206 m)  
11,502 feet (3,506 m)  
HKX8/10-1  
HKX8/10-2  
HKX8/10-3  
18 AWG  
16 AWG  
14 AWG  
1,128 feet  
1,791 feet  
2,857 feet  
(343 m)  
(545 m)  
(870 m)  
18 AWG  
16 AWG  
14 AWG  
112 feet  
179 feet  
285 feet  
(34 m)  
(54 m)  
(86 m)  
230 VAC  
18 AWG  
16 AWG  
14 AWG  
4,145 feet (1,263 m)  
6,579 feet (2,005 m)  
10,496 feet (3,199 m)  
14  
Pelco Manual C1495M-B (10/03)  
 
OPERATION  
Enclosure heaters turn on at 40°F (4°C) and turn off at 60°F (16°C).  
Enclosure blower fans operate continuously.  
SPECIFICATIONS  
MAXIMUM CAMERA AND LENS SIZE  
(With Heater Only)  
1.75 in. H x 3.375 in. W x 10.375 in. L (4.45 x 8.57 x 26.35 cm)  
EHX4E (only)  
10.38 in. L x 3.0 in. diameter (26.36 x 7.62 cm)  
(With Blower Only or Blower and Heater)  
1.75 in. H x 3.375 in. W x 9 in. L (4.45 x 8.57 x 22.86 cm)  
9 in. L x 3.0 in. diameter (22.86 x 7.62 cm)  
EHX4E  
EHX6E  
3.75 in. H x 4.375 in. W x 22.25 in. L (9.53 x 11.11 x 56.52 cm)  
22.25 in. L x 5.0 in. diameter (56.52 x 12.70 cm)  
EHX6E-16  
EHX8E  
3.75 in. H x 4.375 in. W x 14.25 in. L (9.53 x 11.11 x 36.20 cm)  
14.25 in. L x 5.0 in. diameter (36.20 x 12.70 cm)  
5.75 in. H x 5.125 in. W x 22.25 in. L (14.60 x 13.02 x 56.52 cm)  
22.25 in. L x 7.3 in. diameter (56.52 x 18.54 cm)  
EHX10E  
7.75 in. H x 5.75 in. W x 22.25 in. L (19.69 x 14.61 x 56.52 cm)  
22.25 in. L x 9.0 in. diameter (56.52 x 22.90 cm)  
(Design and product specifications subject to change without notice.)  
Pelco Manual C1495M-B (10/03)  
15  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual # Date  
Comments  
C1495M  
9/98  
7/99  
Original version.  
C1495M-A  
Moved certifications to model description. Revised heater kit and blower kit installation instruction, wiring diagrams, exploded  
assembly diagrams, and parts lists. Added specifications.  
C1495M-B  
10/03  
Added solder lug to Figures 1 and 2 and Table A per ECO #03-8634.  
®Pelco, the Pelco logo, Spectra, Genex, Coaxitron, Legacy, Esprit,  
Camclosure, Spectra III, and Spectra III SE are registered trademarks of Pelco.  
© Copyright 2003, Pelco.  
All rights reserved.  
16  
Pelco Manual C1495M-B (10/03)  
 

Pfaff Sewing Machine Hobby 350p User Manual
Philips Blu ray Player BDP3305 User Manual
Philips Cordless Telephone CD445 User Manual
Philips Flat Panel Television 19PFL3505D User Manual
Philips Home Theater System HTS3569 98 User Manual
Philips Network Router PTN3501 User Manual
Philips Recording Equipment HQ9170 User Manual
Planon System Solutions Scanner PS90 User Manual
Plantronics Flat Panel Television 300NS User Manual
Proficient Audio Systems Home Theater System F400BLK User Manual