Pelco Projector Accessories C2224M B User Manual

C2224M-B (12/06)  
PMCL-WMT  
Monitor Mount  
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Installation should be done only by qualified personnel and conform to all local codes.  
6. Only use installation methods and materials capable of supporting four times the maximum specified load.  
7. Only use replacement parts recommended by Pelco.  
8. This unit is designed for indoor use only, and it must not be installed where exposed to rain or moisture.  
Description  
The PMCL-WMT is a tilt/swivel wall mount that can be used to mount any of Pelco’s 200, 300, or 400 Series flat panel LCD monitors. This mount can also  
support most sizes of Pelco’s 500 Series LCD monitors, although a PMCL-V200 adapter plate may be required. This mount can be swiveled 360 degrees to  
allow you to use the monitor in either landscape or portrait view. The mount also allows you to tilt the monitor 35 degrees for the best viewing angle.  
The PMCL-WMT is capable of supporting a maximum load of 90 pounds (40.8 kg).  
Installation  
The following parts are supplied:  
Qty  
1
Description  
Wall bracket  
1
Monitor mount  
4
4
M4 x 10 mm pan head Phillips screws, stainless steel  
Split lock washers  
4
4
M6 x 12 mm pan head Phillips screws, stainless steel  
Flat washers  
1
1
1
10-32 socket head screw  
Flat washer, #10, stainless steel  
Allen wrench, 3/16"  
1
Allen wrench, 5/32"  
To install the tilt/swivel wall mount:  
1. Disassemble the monitor mount from the wall bracket by removing the 10-32 socket head  
screw and flat washer from the underside of the mount. Use the 5/32-inch Allen wrench  
(supplied) to loosen the screw. Slide the two pieces apart and retain the washer and  
screw for reassembly.  
2. Attach the monitor mount to the monitor. Refer to Figure 1 and do one of the following:  
31-inch Monitor or Smaller: Align the monitor to the correct hole  
pattern on the mounting plate. Use the M4 x 10 mm screws and split  
lock washers (supplied) to secure the monitor to the mounting plate.  
or  
Monitors Larger than 31-inches: Align the monitor to the outside  
hole pattern of the monitor plate. Use the M6 x 12 mm screws and  
flat washers (supplied) to secure the monitor to the mounting plate.  
Figure 1. Attaching the Monitor Mount  
 
 
4. Carefully slide the monitor mount into the slots of the wall bracket. Use the 10-32 socket head screw and the flat washer (supplied) to fasten the wall  
Figure 4. Attaching the Wall Mount and Monitor  
5. Using the 3/16-inch Allen wrench (supplied), loosen the button head bolts on the side of the mounting head. Tilt the monitor to the desired angle.  
To secure the monitor in place, retighten the button head bolts.  
Figure 5. Securing the Monitor  
6. To swivel the monitor between portrait and landscape views, loosen the nut on the back side of the mounting head using a 9/16-inch wrench (not  
supplied). Retighten the nut to secure the monitor in place.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
REVISION HISTORY  
Manual #  
C2224M  
Date  
8/06  
Comments  
Original version.  
C2224M-A  
C2224M-B  
11/06  
12/06  
Inserted statement per UL about minimum 2 x 4 wood stud.  
Added hardware information for large monitors per ECO 06-17078.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura,ExSite, and Spectra III are trademarks of Pelco.  
©Copyright 2006, Pelco. All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc.  
 
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted  
pair transmission products.  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Three years on Spectra® IV products.  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
Two years on Spectra III, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.  
The lamp and color wheel will be covered for a period of 90 days. The air filter is not  
covered under warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed  
to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelco’s liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
 
Australia Canada Finland France Italy Russia Singapore Spain Sweden The
 
Netherlands United
 
Arab Emirates
 
United Kingdom
 
United States  
|
|
|
|
|
|
|
|
|
|
|
|

Pelican Home Safety Product 2140 User Manual
Philips Camcorder CAM295 User Manual
Philips CD Player AZ1830 User Manual
Philips Cordless Telephone CD1554B User Manual
Philips Electric Shaver 3801XL User Manual
Philips Projection Television 69165 31 User Manual
Philips Speaker System FWM70 User Manual
Polaroid Digital Camera PZ2320AF User Manual
Poulan Lawn Mower 178493 User Manual
ProMounts TV Mount UFPRO100 User Manual