Philips TV Mount SQM5822 User Manual

Register your product and get support at  
SQM5822/27  
EN Fixed wall mount  
 
• Safety gear and proper tools must  
be used. Failure to do so can result in  
property damage and/or serious injury.  
• A minimum of two people are required  
for this installation. Do not attempt  
to install this mount alone under any  
circumstance.  
1 Important  
Take time to read this manual before you  
use your wall mount. It contains important  
information and notes regarding operating your  
wall mount.  
• Follow all instructions and  
© 2009 Koninklijke Philips Electronics N.V.  
All rights reserved. Reproduction in whole or in  
part is prohibited without the written consent of  
the copyright owner. Trademarks are the  
property of Koninklijke Philips Electronics N.V.  
or their respective owners.  
recommendations regarding adequate  
ventilation and suitable locations for  
mounting your display. Consult the  
owner’s manual for your display for  
more information.  
• This mount is equipped with a safety  
device that must be used whenever  
the mount holds a display. Not using  
the safety device can cause property  
damage, serious injury, or death.  
BWarnings  
• Make sure these instructions are read  
and thoroughly understood before  
attempting installation. If you are  
unsure of any part of this installation,  
contact a professional installer for  
2 Your fixed wall mount  
assistance or contact Customer Service Congratulations on your purchase and welcome  
at 1-919- 573-7854.  
to Philips!  
• This product has been designed  
for application on a vertical wall in  
commercial and residential buildings,  
constructed of wood wall studs or  
masonary (solid concrete, brick, and  
stone). If you are unsure of your wall  
To fully benefit from the support that Philips  
offers, register your product at  
Designed to fit most TV brands with a focus  
composition or for assistance with other on safety and ease of use. Includes Easy 1-2-3  
surfaces, contact a qualified installer.  
• This product is not designed for use on  
walls constructed of metal studs. If you  
are unsure of your wall composition  
or for assistance with other surfaces,  
contact a qualified installer.  
installation kit, complete with: all necessary  
hardware for mounting on different types of  
walls, mounting templates and bubble level. C-UL  
US listed for weight capacity up to 132lbs.  
• The wall or mounting surface must be  
capable of supporting the combined  
weight of the mount and the display;  
otherwise the structure must be  
reinforced.  
• Do not exceed the maximum load  
capacity of 132lbs for this product.  
• Fits 30-55” screens  
3
 
2.1 What’s in the box.  
Wall mount  
Bag #1  
Cotter pin  
(A) M4x12 Bolt (x4)  
(B) M4x30 Bolt (x4)  
(E) M5x30 Bolt (x4)  
(H) M6x35 Bolt (x4)  
(K) M8x40 Bolt (x4)  
(N) Large Spacer (x4)  
(Q) M8x63 Lag Bolt (x6)  
(C) M4 Lock Washer (x4)  
(F) M5 Lock Washer (x4)  
(I) M6 Lock Washer (x4)  
(I) M8 Lock Washer (x4)  
(O) M6 Washer (x4)  
Bag #2  
Bag #3  
Bag #4  
Bag #5  
Bag #6  
(D) M5x12 Bolt (x4)  
(G) M6x12 Bolt (x4)  
(J) M8x16 Bolt (x4)  
(M) Small Spacer (x4)  
(P) Concrete Anchor (x6)  
(R) Lag Bolt Washer (x6)  
2.2 What you’ll also need.  
• Phillips head screwdriver  
• Ratchet or driver with 1/2” (13 mm) socket  
• Portable or electric drill  
• 1/4” (6 mm) drill bit and stud finder for drywall installation  
• 3/8” (10 mm) masonry bit for concrete installation  
• Stud finder  
4
 
4
5
With the help of another person, place the  
mount against the wall and level it using the  
bubble guide.  
While another person holds the mount in  
place, mark four locations (two per stud)  
on the wall where the mount is to be  
installed. Be sure to use the center of each  
stud. (these marks should line up with  
the ones made in step 3 above using the  
template).  
Set the mount aside and drill a 1/4” (6 mm)  
pilot hole at each marked location.  
Place the mount back against the wall and  
secure it using the lag bolts (Q) and lag bolt  
washers (R) provided. Do not over-tighten  
these bolts and do not release the mount  
until all bolts are in place.  
Once all (4) lag bolts are in place you must  
tighten each one. (note: be sure not to over  
tighten). 1  
3 Installing your wall mount  
In this chapter, the basic steps to get you started  
are described.  
B Warning  
Carefully read the safety precautions  
in “Section 1 Important” before you  
install the wall mount.  
6
7
3.1 Mounting the wall plate (drywall)  
B Warning  
For safety reasons, this mount must  
be secured to two adjacent wood  
studs at least 16” apart.The studs  
must be capable of supporting the  
combined weight of the mount and  
display.  
8
1
1
2
See enclosed mounting template for  
diagram and guide of how to mount  
properly on the wall.  
Using a stud finder, locate and mark two  
adjacent studs for securing the mount  
(make sure your marks are in the center of  
each stud).  
3.2 Mounting the wall plate (concrete)  
D Note  
Once studs have been located you will  
need to verify with a hammer and a  
nail  
B Warning  
For safety reasons, the concrete wall  
must be capable of supporting the  
combined weight of the mount and  
display.  
A) Simply place the nail over your  
mark on the wall and tap in with  
hammer. if the nail encounters  
resistance and is secure in wall you  
have verified a stud location  
B) If it just pushes through with no  
resistance you will need to start  
over and locate the stud.  
Using the enclosed mounting template,  
place the diagram against the wall and mark  
four locations (two per stud) on the wall  
where the mount Is to be Installed. Be sure  
to use the center of each stud.  
1
2
See enclosed mounting template for  
diagram and use enclosed mounting  
template as a guide for precision mounting.  
Using the enclosed mounting template,  
place the diagram against the wall and mark  
six locations on the wall where the mount  
Is to be Installed.  
3
5
 
3
4
5
6
With the help of another person, place the  
mount against the wall and level it using the  
bubble guide.  
While another person holds the mount in  
place, mark six locations on the wall where  
the mount is to be installed.  
Set the mount aside and drill a 3/8” (10  
mm) pilot hole at each marked location.  
Remove any excess dust from the holes.  
Insert a concrete anchor (P) into each hole  
so that it is flush with the concrete surface.  
A hammer can be used to lightly tap the  
anchors into place if necessary.  
3.3 Attaching the arms to the display  
B Warning  
Use extra care during this part of the  
installation.Avoid laying your display  
face down if possible as it may damage  
the viewing surface.  
1
Examine the back of your television.  
If the back of your display is flat: You  
will be using one of the shorter bolts from  
the hardware kit.  
3
7
Place the mount back against the wall and  
secure it using the lag bolts (Q) and lag bolt  
washers (R) provided. Do not over-tighten  
these bolts and do not release the mount  
until all bolts are in place. 2  
3
2
If the back of your display is curved  
or recessed: You will be using one of the  
longer bolts and a spacer.  
4
4
8
Once all (6) lag bolts are in place you must  
tighten each one. Be sure not to over  
tighten.  
D Note  
If the concrete wall is covered  
by a layer of plaster or drywall,  
the concrete anchor must pass  
completely through the layer to rest  
flush with the concrete surface.  
2
Determine the correct diameter bolt to  
use by trying one bolt each from Bags 1  
- 4 of the hardware kit. Do not force any  
of the bolts – if you feel resistance stop  
immediately to avoid damaging your display.  
6
 
3
Attach the arms to the back of your display  
using the bolts identified in Steps 1 and  
2 and the corresponding lock washer  
(C, F, I, or L).You will need to use the M6  
washers (O) if you are using the M4, M5,  
or M6 bolts. If your display has a curved or  
recessed back, you may also need to use a  
spacer (M or N).  
4 Mounting and adjusting  
1
With the help of another person, carefully  
lift your display and place it on the wall  
plate. Do not release the display until the  
mounting arms have securely hooked onto  
the mount.  
6
4
Make sure the screws are snug, but do not  
over-tighten. 5  
6
5
2
Carefully hook the display onto the wall  
plate 7  
E Tip  
Use a longer bolt and spacer for  
7
displays with curved or recessed  
backs. Do not use the M6 washer (O)  
if you are using the M8 bolts (J or K).  
B Warning  
Insert the safety bar at the center of  
the mount to avoid having the display  
accidentally knocked off the mount.  
3
This MUST be done in order to secure  
the display to the mount. NOTE:A cotter  
pin (included) Is used to secure the arms  
to the mount OR a padlock (not included)  
can be inserted into the hole at the end of  
the saftey bar to help prevent theft of your  
display. A small cotter pin can be used to  
secure your display to the mount. (included)  
7
 
4
Once the tv is fitted properly on to the wall  
bracket, the security bar must be put into  
place. 8  
5 Guarantee and service  
Please contact Philips directly if you have any  
questions in the installation process of the wall  
mount. Call 1-919-573-7854.  
8
Limited One-YearWarranty:  
Philips warrants that this product shall be free  
from defects in material, workmanship and  
assembly, under normal use, in accordance with  
the specifications and warnings, for one year  
from the date of your purchase of this product.  
This warranty extends only to the original  
D Note  
Slide arm through slots in wall plate & purchaser of the product, and is not transferable.  
brackets  
To exercise your rights under this warranty, you  
must provide proof of purchase in the form of  
an original sales receipt that shows the product  
name and the date of purchase. For customer  
support or to obtain warranty service, please  
call 1-919-573-7854.THERE ARE NO OTHER  
EXPRESS OR IMPLIEDWARRANTIES. Philips’  
liability is limited to repair or, at its sole option,  
replacement of the product. Incidental, special  
and consequential damages are disclaimed where  
permitted by law.This warranty gives you specific  
legal rights.You may also have other rights that  
vary from state to state.  
5
6
Once the security bar is slid into the  
appropriate slots, a lock(not provided) may  
be placed for additional security.  
A small cotter pint can be used to secure  
your display to the mount. (included). 9  
9
Register your product and get support at  
8
 
 
© 2009 Koninklijke Philips Electronics  
All rights reserved.  
SQM5822_27_UM_V2.0  
 

Pelco CRT Television PMM12A User Manual
Pelco Home Security System PT7800 User Manual
Philips Blu ray Player bdp5000 User Manual
Philips Flat Panel Television 14AA3327 User Manual
Philips Home Theater System LX9000R 25S User Manual
Philips Washer 12NC User Manual
Plantronics Headphones HL10 User Manual
Poulan Trimmer PPB100E User Manual
Profoon Telecommunicatie Answering Machine TAM 60X User Manual
PYLE Audio Car Video System PLVSR10BK User Manual