|
PM3
Front Cover Art
Setup
Setup, cont.
Battery Installation
TV Volume/Mute Punch-Through Feature
1. On the back of the remote,
push down on the tab and
lift the cover off.
2. Match the batteries to the
+ and - marks inside the
battery case, then insert 2
AAA Alkaline batteries.
3. Press the battery cover
back into place.
The TV Volume/Mute punch-through feature lets you
control the Volume and Mute function of your TV in any
mode programmed to be a VCR, DVD, CABLE or SAT
device, without needing to change to TV mode.
VCR/DVD Punch-Through Feature
Punch-through to VCR/DVD mode i.e. the 6 keys (PLAY,
PAUSE, STOP, FF, REWIND, andREC) is only allowed
in modes programmed for TV or Cable codes.
Battery Saver
Your remote automatically
turns off if the buttons are
depressed more than 30
seconds. This will save your
batteries should your remote
get stuck in a place where the
buttons remain depressed
(e.g., between the sofa
cushions).
Code Setup
The CODE SEARCH button is used to setup the remote.
You can either setup the remote using the code for your
brand of product, from the code tables (on separate
sheet), or you can search through the library of codes
until you find a code that works for your product.
Please refer to “Programming with Code Search” on page
11 for more information on using the code search feature
to learn how to search through the library of codes for
your products.
Code Saver
NOTE: You can store any kind of code under any mode
(except TV). I.E. you can store a VCR code under the
CBL button, or a DVD code under the VCR button, etc.
However, you can only store TV codes under the TV
button.
You will have up to 10 minutes to change the batteries
in your remote without losing codes you have
programmed. However, do not press any buttons until
batteries are installed in the remote. If buttons are
pressed without batteries in the remote, all codes will be
lost.
PO WE R
VCR
D VD
TV
CBL
Power-On Default
QUIT
The remote powers on in TV mode.
OK
INFO
MENU
SELECT
IN/OUT
C ODE
S EAR CH
S UB
P R EV.
C HAN
S LEE P
TITLE
CODE SEARCH
R EP EAT
4
5
Button Functions
Button Functions, cont.
Some buttons on the remote might have functions that
are referred to by different names on the device you are
controlling. E.G. PREV.CHAN may be called RECALL, or
ENTER may be called DISPLAY. These differences depend
on the brand and model of your product. Also, this
remote can only operate features that exist on your
product. E.G., your product must have PREV.CHAN
ability for the PREV.CHAN button to operate this feature.
CHANNELUP/
DOWNChanges
the channels.
POWER
VOLUMEUP/
DOWNChanges
the volume level
of the product,
normally the TV.
QUITexits
Turns
from Menu
mode.
product On
or Off.
MENUIN/OUT
Toggles in and out
of menu mode.
Accesses the Menu
functions of the
device you are
PO WE R
CBL
MUTETurns off
the TV sound
while the picture
remains. Use for
OK/SELECTin
Menu mode.
TV, VCR/DVD, Indicator light
CBLSelects
product to be
operated.
Lights when any
button is pressed.
VCR
D VD
TV
QUIT
controlling.
OK
PREV.CHAN Returns
to the previously
PO WE R
CHAPTER+/-
controls DVD track
selection i.e. DVD
Track Skip Up/Down
(in DVD mode). Note
the DVD Transport
keys also control DVD
when in DVD Mode.
VCR
selected channel, or
DVD repeat toggle.
REPEAT performs DVD
players “A-B Repeat”
(or RPT A.B) function
for repeat play of
INFO
MENU
D VD
CBL
SELECT
IN/OUT
TV
QUIT
C ODE
S EAR CH
S UB
TITLE
P R EV.
C HAN
S LE EP
OK
R EP EAT
current Chapter or
Track.
INFO
MENU
SELECT
IN/OUT
INFO/SELECT
displays/selects
on-screen channel
information, etc.
C ODE
S UB
P R EV.
C HAN
CC(SUBTITLE)
TV Closed
Caption (if your
TV has this
feature) or DVD
Subtitle toggle.
S LE EP
S EAR CH
TITLE
INPUT
TV/
VCR
R EP EAT
ENT
SLEEPTurns off the
TV after a period of 1
to 99 minutes.
S CAN R EW
REC
PLAY
S CAN FF
PAUS E
STOP
CODE SEARCH For setup.
INPUT
TV/VCR/INPUT
For some TVs, press
repeatedly to select
from available
TV/
VCR
ENT
NUMBERS
Enter numbers for
direct channel
S CAN R EW
REC
PLAY
S CAN FF
PAUS E
STOP
viewing sources
(TV, CBL, etc.).
selection. Some
products require Enter
to be pressed after
channel selection.
RECORD, PLAY, STOP,
REW, FF, PAUSEVCR
control buttons operate
your VCR even when the
remote is set to operate
the TV. Also operates
DVD Scan -/+.
Note: The REC button must
be pressed TWICE to record
from your VCR. For some
brands of VCRs, you might
need to press the REC
ENTER
Used after direct
channel number
entry to immediately
change to the
button once, then press it
again for three seconds.
selected channel.
6
7
Advanced Button Functions
Advanced Functions, cont.
DVD Functions
VCR/DVD Punch-Through Feature
SCAN+ and SCAN- buttons control the speed of Fast
Forward and Reverse Playback respectively.
CHAPTER+ andCHAPTER-buttons respectively
locate the succeeding or preceding Chapters or Tracks
on a disc.
SUBTITLE button turns the subtitles on or off.
REPEAT button performs DVD players “A-B Repeat” (or
RPT A.B) function for repeat play of current Chapter or
Track.
INFO/SELECTbutton brings up DVD Display or
Control Menu for Chapter/Track/Title number, Time
remaining/elapsed indication, system information, etc.
QUIT button is used to Exit or Clear on-screen Menu
displays.
PLAY button is used to start Disc playback and for
Menu selection on some DVD players.
STOP button stops Disc playback.
This remote lets you Punch-through to the last VCR or
DVD device used. Normally other types of remotes only
punch-through (from another Mode) on the 6 VCR
buttons, to the device programmed under the VCR
Mode button. This is not much use if you are using a
DVD programmed under a Mode other than VCR. This
remote punches-through to the last VCR or DVD device
you used. For example, if you have 3 DVD/VCR devices
programmed into this remote, the last one you accessed
on the remote will be the one that has control of the 6
VCR/DVD buttons when in any other mode.
TV/VCR/INPUT
When in TV mode theTV/VCR/INPUTbutton performs
the INPUT source switch function.
When in a mode that has been programmed for VCR the
TV/VCR/INPUT button performs the TV/VCR antenna
switch function.
When in a mode that has been programmed for Cable the
TV/VCR/INPUT button performs the A.B switch
function.
When in a mode that has been programmed for SAT the
TV/VCR/INPUT button performs the TV/SAT switch
function.
When in a mode that has been programmed for DVD the
TV/VCR/INPUT button performs the DVD Setup
function.
PAUSE button pauses Disc playback - press PLAY to
resume.
INPUTbutton activates the DVD Player’s SETUP Menu.
MENUIN/OUT
The Menu In/Out button allows you to toggle in and out
of Menu Mode. Pressing Menu In/Out brings up your
device Menu. While in Menu mode the remote’s red
indicator light blinks continuously. The remote will exit
Menu Mode after 20 seconds if no keys are pressed.
While Menu Mode is active, the Menu, Channel,
Volume, Mute and Mode keys perform the following
functions:
TV/VCR and TV/DVD Combo units
Note that for some TV/VCR and TV/DVD combo units
you might need to set up two different buttons to
control both parts of the combo unit. E.G., (referring to
the Direct Code Entry section on the following page)
you might need to set up a code under the TV button to
control the TV part of the combo unit AND a separate
code for the VCR or DVD under any other button you
choose.
MENU IN/OUT Exits/Enters Menu mode.
CHANNEL UP/DOWN Up/Down commands for on-
screen Menu navigation.
VOLUME UP/DOWN Right/Left commands for on-
screen Menu navigation.
MUTE OKcommand for on-screen Menu selection.
TV Mode Key Quit, Exit or Clear command to quit on-
screen Menu and return the remote to normal operation
(red indicator is now off). Note this action is also
available by pressing any Mode key.
Misc.
OK means same as SELECT - some manufacturers use
OK label and others use SELECT label on their remotes.
CC will activate the Closed Caption feature if your
device has that feature.
8
9
Code Entry
Code Entry, cont.
Direct Code Entry
Programming with Code Search
1. Press and hold the CODE SEARCH button until the
red indicator stays on, then release the CODE
SEARCH button.
2. Press and release the desired mode button (TV, VCR,
etc.). The red indicator blinks, then stays lit.
3. Enter the 3 digit code from the code tables (on
separate sheet). Note: after a valid code entry, the
red indicator turns off. For an invalid code, the red
indicator flashes.
4. With your device on, press CHANNEL UP. If the
device responds, no further programming is
required. Note: If some buttons do not operate your
equipment, try one of the other codes for your
brand.
If your product does not respond after you have tried all
the codes for your brand, or if your brand is not listed,
try searching for your code by following these steps.
1. Manually turn on the device (TV, VCR, etc.) to be
controlled.
2. Press and hold the CODE SEARCH button until the
red indicator stays on, then release the CODE
SEARCH button.
3. Press and quickly release the desired mode button
(TV, VCR, etc.). The red indicator blinks off once.
4. Press the CHANNEL UP button repeatedly (up to 300
times) until the device to be controlled changes
channel. The red indicator blinks off with each
button press. If you accidentally overshoot the
code required, press the CHANNEL DOWN button
to backtrack through the library until the device
changes channel. Pressing CHANNEL UP changes
direction to forward again.
PO WE R
VCR
D VD
TV
CBL
2.
5. Press and release MUTE to install the code.
QUIT
Most users will store VCR codes under the VCR button,
Satellite codes underSAT , etc. If (for example) you want
to store a VCR code under SAT, first follow the procedure
for Direct Code Entry (page 10) and press SAT in step 2
of Direct Code Entry, then enter ANY VCR code in step 3
of Direct Code Entry. Then follow the steps above for
Code Search (or Brand Search, page 12).
OK
INFO
MENU
SELECT
IN/OUT
C ODE
S EAR CH
S UB
P R EV.
C HAN
S LEE P
TITLE
1.
3.
R EP EAT
Note: If the device does not have a CHANNEL UP
button, use PLAY (VCR only) or POWER instead. Code
Search starts from the currently stored three digit
number under that mode.
Write your codes down here for easy reference later.
VCR
D VD
TV
CBL
3.
Type
TV
Type stored
TV
Code
QUIT
4.
5.
OK
VCR
DVD
Cable
INFO
MENU
SELECT
IN/OUT
C ODE
S EAR CH
S UB
P R EV.
C HAN
S LE EP
TITLE
2.
R EP EAT
10
11
Code Entry, cont.
Code Entry, cont.
Code Search by Brand
Brand Search Table
Look up your brand in the appropriate column (TV, VCR,
etc.). Look to see what digit (1, 2, 3, etc.) applies to your
brand, and enter it in step 4 of “Code Search by Brand”
on the previous page.
Lets you search for a code for a specific Brand within
the Code Library for a particular manufacturer.
1. Turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the CODE SEARCH button until the
red indicator remains on, then release CODE
SEARCH button.
3. Press and quickly release the desired mode button
(TV, VCR, etc.). The red indicator blinks off once.
4. Press and release the numeric button (0-9)
corresponding to desired Manufacturer (see table on
next page). The red indicator blinks off once. Note,
pressing “0” performs a full library search same as
normal Code Search Method on previous page.
5. Press the CHANNEL UP button ((or POWER or PLAY
(VCR only)) repeatedly until the device to be
controlled changes channel. The red indicator blinks
off with each button press. If you accidentally
overshoot the code required, press the CHANNEL
DOWN button to backtrack through the library until
the device changes channel. Pressing CHANNEL UP
changes direction to forward again.
6. Press and release MUTE to install the code.
Brand Search Method entry is now complete.
Note: When all codes under a Brand have been searched
the red indicator flashes rapidly for 3 seconds.
PO WE R
VCR
D VD
TV
CBL
3.
QUIT
5.
6.
OK
INFO
MENU
SELECT
IN/OUT
C ODE
S EAR CH
S UB
P R EV.
C HAN
S LE EP
TITLE
2.
4.
R EP EAT
12
13
Sleep Timer
Code Identification
The Sleep feature enables the remote to turn off the TV
after a period of 1 to 99 minutes. Remote is to be in TV
mode to set a Sleep Timer. This feature works even if
your TV does not have this feature.
Code Identification Feature
The Code Identification Feature allows you to identify
the three digit library code stored under your device key.
For example, if you want to find out what three digit
code is stored under your TV device key, follow the six
steps below:
1. Press and release the TV Mode button.
2. Press and hold the SLEEP button until red indicator
remains on (occurring after approx. 2-3 seconds).
1. Press and hold the CODE SEARCH button until the
red indicator stays on. Release the CODE SEARCH
button.
QUIT
OK
2. Press and release the desired mode button (TV,
VCR, etc.). The red indicator blinks, then stays lit.
3. Press and release the CODE SEARCH button. The
red indicator blinks off.
INFO
MENU
SELECT
IN/OUT
4. To find the first digit for the code stored under the
mode key pressed in step 2, press each numeric key
from 0-9 in turn. When the red indicator blinks off
the number you pressed is the first digit for the code
you are searching for.
5. To find the second digit, repeat step 4, this time
when the red indicator blinks off this is the second
digit.
C ODE
S UB
P R EV.
C HAN
S LE EP
TITLE
S EAR CH
R EP EAT
3. Release the SLEEP button.
4. Press and release the numeric buttons (01-99) for the
time required. The red indicator blinks off to indicate
button press acceptance and remains off after the
second button press.
6. Repeat step 4 again to find the third digit.
5. TV Sleep Timer now set.
6. Leave the Remote pointing towards
the TV with an unobstructed path.
PO WE R
VCR
D VD
TV
CBL
To cancel the Sleep Timer, press and hold the SLEEP key
for 2-3 seconds until the red indicator blinks or press
and release the POWER button in TV Mode.
2.
QUIT
OK
INFO
MENU
SELECT
IN/OUT
C ODE
S EAR CH
S UB
P R EV.
C HAN
S LEE P
TITLE
1, 3.
R EP EAT
4.
14
15
Product Operation
Troubleshooting
After the batteries are installed and you have
programmed the remote for the codes that operate your
products, you can use your remote to operate a TV, VCR,
DVD, or Cable Box.
Remote does not operate your product.
•
Press the mode button of the product you want to
control.
•
•
Program the remote with a new code.
Install new batteries. (You might have to reprogram
your remote after installing new batteries.)
Remote may not be compatible with your product.
•
Remote does not operate some features of your product.
•
•
Program remote with a new code.
Remote may not be able to operate all features of
your product or button names might be different
than your product.
Indicator light blinks after you program a product
code.
TV (PressTVFirst)
•
•
Remote did not accept the code.
Try to program the code again or try a different
code.
For help with setup, please call: 919-573-7854.
VCR
DVD Player
(PressVCR/DVDfirst)
(PressVCR/DVDfirst)
Cable Box
(PressCBLfirst)
To Operate:
1. Press theTV, VCR/DVD, or
CBL button (depending on
which product you want to
operate).
2. Aim the remote at the product.
3. Press POWER to turn on the
product.
4. Press other buttons to operate
the features of your product.
16
17
Notes
Notes
18
19
90 Day Warranty
This product is manufactured to PHILIPS MAGNAVOX
specifications and is free from defects in material,
workmanship and assembly. This warranty extends only
to the original purchaser and is nontransferable. Should
a defect occur under normal operating conditions within
90 days from the date of purchase, PHILIPS
MAGNAVOX will provide a comparable replacement free
of charge within the warranty period, to the original
purchaser. Defective product must be returned, with the
dated proof of purchase, to the place of purchase for
replacement. This warranty does not extend to the
product if it has been damaged or rendered defective as
a result of accident, misuse, abuse, tampering with or
modification. THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL PHILIPS
MAGNAVOXBELIABLEFORSPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES,
WHETHERINCONTRACT,TORTORNEGLIGENCE.
Some States do not allow limitations on how long an
implied warranty lasts, so the above limitation may not
apply to you. Some States do not allow exclusion or
limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This
warranty gives you specific rights and you may also
have other rights, which vary from State to State.
Made in China-TC, Quality Assured in USA
Clifton, NJ 07014-1115
PM3 Back
Cover Art
|