Princeton VCR 4411 0118 User Manual

4411-0118 Rev. A  
Quick Start Guide—Single Head Controller (CameraLink)  
Page 1  
This Quick Start Guide provides instructions for basic setup of  
a MegaPlus camera and MegaPlus Central Control Software.  
For additional information, please consult the MegaPlus User’s  
Manual.  
2. Select the option to Install MegaPlus Central Software  
and follow the onscreen instructions. The MegaPlus  
Camera Installer will start automatically after the  
application files have been installed.  
3. Step 1 of the Camera Installer adds an entry for your  
MegaPlus camera into the camera list. A descriptive  
name for the camera can be added to help identify it.  
Equipment Required for Setup  
User Supplied items:  
PC running: Windows XP, Windows 2000 Pro (SP2) or  
Windows NT 4.0 or higher  
4. In Step 2, specify your CameraLink interface options.  
Crossover Ethernet cable (for firmware updates)  
5. Install the framegrabber application software and  
follow the instructions provided by the framegrabber  
manufacturer.  
Interface Option and Accessories:  
CameraLink Framegrabber hardware and software  
CameraLink cable(s)  
Optional: RS-232 serial for camera control only  
Select from the following options:  
Princeton Instruments Package Contents:  
CameraLink Serial—Select this interface if you will be  
using a CameraLink Framegrabber and the CameraLink  
serial port, then select the vendor’s DLL from the drop  
down list.  
Camera Controller  
Software Developers Kit (SDK)  
CD with User’s Manual and MegaPlus Central  
Software  
Power Supply  
Camera Head  
Camera Head cable  
COM Port Serial—Select this interface if you will be using  
the DB9 connector on the rear panel of the Camera  
Controller and a separate RS–232 serial cable to control the  
camera. Specify the COM port you are connected to on the  
host with the following Connection Parameters:  
Hardware Setup  
Before proceeding, make sure that your CameraLink  
Framegrabber hardware and software are installed  
properly.  
Caution: Make sure the MegaPlus Camera Controller  
power switch is turned to the OFF position before  
connecting the cables!  
9600 baud  
1 stop bit  
No flow control  
No parity  
Data bits  
1. Connect the cable from the Camera Head to the camera  
port labeled Remote Head on the Camera Controller.  
2. If using an EC11000 or an EC16000 Camera Head, connect  
the Camera Head to the auxiliary power supply.  
3. Connect a CameraLink cable from the CameraLink  
connector on the back panel of the Camera Controller to  
the Connector of your CameraLink Framegrabber.  
Camera Controller front panel  
4. Connect the Camera Controller to the power supply.  
Software Installation  
Note: MegaPlus Central Software is used to control camera  
through serial commands only. A third party framegrabber  
software must be used to capture and display images.  
Camera Controller back panel  
1. Install the MegaPlus Central software by inserting the  
MegaPlus software CD into the computer’s CD-ROM  
drive. The menu program should start automatically. If  
your system does not start the menu, open Windows  
Explorer, go to the Install folder on the CD and double-  
click on the “MenuBox.exe” application on the CD.  
Continued on page 2  
 

Peavey Musical Instrument Amplifier Deltabass User Manual
Pelco Home Security System C1554M A 4 05 User Manual
Pelco Home Security System CC3751H 2 User Manual
Philips Car Speaker SB365 User Manual
Philips CRT Television 14PT2322 User Manual
Philips CRT Television VR805 User Manual
Philips Network Card KX TDA0490 User Manual
Pioneer Stereo System DEH 2300 User Manual
Precision Power Car Speaker A265C User Manual
Pro Optic Camera Accessories PROFH User Manual