PYLE Audio Speaker System PLMRKT4A User Guide

PLMRKT4A  
4 CHANNEL WATERPROOF AMPLIFIED  
6.5” MARINE SPEAKER SYSTEM  
PLMRMP3A  
4 CHANNEL WATERPROOF  
MARINE POWER AMPLIFIER  
OWNER’S MANUAL  
 
PLMRMP3A 4 Channel Waterproof Marine Power Amplifier  
● 4 x 100 Watts RMS at 4 Ohms  
● 4 x 200 Watts Max at 4 Ohms  
● 4 x 300 Watts RMS at 2 Ohms  
● Electronic Crossover Network  
● 2 Ohms Stereo Stable  
● Anti-Thump Turn-On  
● Soft Turn On/Off  
● Adjustable High Low Level Inputs  
● RCA Line Input  
● Power Protection Circuitry  
● Volume Gain Remote Control  
● T.H.D: <0.05%  
● S/N Ratio: >95dB  
● Channel Separation: >65dB  
● Frequency Response: 10Hz- 40kHz  
● Fuse : 10A  
● Dimensions: 6.10”Lx3.35”Wx1.38”H  
Accessories:  
iPod / MP3 Waterproof 3.5mm Stereo to RCA Adaptor  
Remote Control for Volume Gain  
What is inclued?  
When first unpacking your new amplified marine speaker system, Please  
check first that the package contains all of the items below. If something  
is missing, contact the store where you purchased the product.  
PLMRKT4A  
Two Pairs 6.5'' 2-Way Marine Speaker  
One Piece PLMRMP3A  
One Piece iPod / MP3 Waterproof Poly Bag  
One Piece iPod / MP3 Waterproof 3.5mm Stereo to RCA Adaptor  
One Piece Remote Control for Volume Gain  
PLMRMP3A  
One Piece 4 Channel Waterproof Marine Power Amplifier  
One Piece iPod / MP3 Waterproof 3.5mm Stereo to RCA Adaptor  
One Piece Remote Control for Volume Gain  
2
 
Controls, Input and Output Cables:  
Installation precautions  
1
2
Before you drill or cut any holes, investigate your vessel’s layout very carefully.  
Take special care when you work near the gas tank, fuel lines, hydraulic lines  
and electrical wiring.  
3
dB GAIN  
+
MAX  
MIN  
Never operate the amplifier when it is unmounted. Attach all audio system  
components securely within the amplifier to prevent damage, especially in an  
accident.  
Do not mount this amplifier so that wire connections are unprotected. in a  
pinched condition, in contact with any metal surfaces in your marine vessel,  
or likely to be damaged by nearby objects.  
4
The switches and gain settings are located behind a watertight plug, which  
also lights up when the amplifier is on. Be sure to replace the plug when  
finished with adjustments  
Before making or breaking power connections in your system, disconnect the  
marine vessel battery. Confirm that your head unit or other equipment is turned  
off while connecting the input jacks and speaker terminals.  
1
The INPUT LEVEL switch selects the input sensitivity of the amplifier. If  
you are connecting to a LINE level source (typically any RCA type  
connection) then the switch should be in the LINE (out) position. When  
connecting to loudspeaker outputs or headphone or high level sources  
then set the switch to the SPEAKER (in) position.  
If you need to replace the power fuse, replace it only with a fuse idenetical to  
that supplied with the amplifier, Using a fuse of a different type or rating may  
result in damage to your audio system or your amplifier which is not covered  
by the manufacturer’s warranty.  
2
The POLARITY switch allows the user to optimize bass performance in  
the case that there are more than 1 set of loudspeakers producing bass  
in the system. Play some music with strong bass content and listen with  
the switch alternately in the NORMAL and REVERSE position until it can  
be determined which setting results in more pleasing bass response. If  
in doubt, or if any interaction with other speakers is unlikely, then leave  
the switch in the NORMAL position.  
Don’t misuse the level control!  
Do not mistake the input level control for a volume control! It is designed  
ONLY to match the output level of your audio source to the input level of  
your amplifier.  
3
The GAIN control adjusts the overall level of the amplifier. When using  
the amplifier without volume control the level should beset to achieve a  
balance with other loudspeakers in the system. As arule, keep the gain  
setting as low as possible while still insuring that the system will reach  
full output power. When using the system with external volume control,  
set the external Volume Control to FULL (clockwise) and adjust the gain  
on the amplifier until full output power is reached. Full output power level  
can be determined by turning the gain control clockwise until the apparent  
loudness does not appear to increase any more. Leave the control at the  
setting where this begins to become apparent.  
Do not adjust this input level to maximum unless your input level requires it.  
Ignoring these instructions will result in an input overload to the amplifier,  
and excessive audio distortion. It can also cause the protection circuit to  
engage.  
3
4
 

RCA CRT Television F27615 User Guide
RCA MP3 Player M63 User Guide
RCA TV VCR Combo 13V401TV User Guide
Rockford Fosgate Speaker P1S4 12 User Guide
Russell Hobbs Refrigerator RHUCFF48B User Guide
Ryobi Chainsaw P542 User Guide
Samsung Flat Panel Television LA46A850S1R User Guide
Samsung Laptop NP680Z5E X01US User Guide
Samsung Security Camera SCC B5396 User Guide
Sanyo Battery Charger UF553048F User Guide